rectifier diode RR1VWM6S ? series ? dimensions (unit : mm) ? land size figure (unit : mm) standard rectifier ? applications general rectification ? features 1) low forward voltage ? structure 2) 3) small mold type (pmde) ? taping dimensions (unit : mm) ? construction silicon diffused junction type ? absolute maximum ratings (t l = 25c) repetitive peak reverse voltage v rm v reverse voltage v r v junction temperature t j c storage temperature t stg c ? electrical characteristics (t j = 25c) symbol min. typ. max. unit v f 0.9 1.08 1.2 v reverse current i r --10 ? a thermal resistance r th(j-l) --30c/w forward voltage parameter a i fsm non-repetitive forward surge current 60hz half sin wave, 15 a average current i o on glass epoxy substrate, 60hz half sin wave , resistive load unit 600 parameter conditions duty Q 0.5 junction to lead direct voltage i f =1a conditions non-repetitive at t j =25oc - - v r =600v t l =125c high current overload capacity 1 600 175 ? 55 to ? 175 symbol limits pmde anode cathode rohm : pmde dot (year week factory) + day 1.1 2.0 0.8 0.5 0.8 1/4 2016.09 - rev.a datasheet www.rohm.com ? 2015 rohm co., ltd. all rights reserved.
RR1VWM6S ? electrical characteristic curves 0.1 1 10 0 5 10 15 20 25 30 f = 1mhz t a = 25 c 0.1 1 10 100 110100 t j = 25 c peak surge forward current : i fsm (a) forward current : i f (a) forward voltage : v f (mv) v f -i f characteristics reverse current : i r (na) reverse voltage : v r (v) v r -i r characteristics capacitance between terminals : c t (pf) reverse voltage : v r (v) v r -c t characteristics number of cycles i fsm -cycle characteristics 1cyc. 8.3ms i fsm 8.3ms 0.01 0.1 1 10 100 1000 10000 100000 0 100 200 300 400 500 600 t j = 25 c t j = 175 c t j = 75 c t j = 125 c t j = ? 40c 0.001 0.01 0.1 1 10 0 200 400 600 800 10001200140016001800 t j = 75 c t j = 25 c t j = 125 c t j = 175 c t j = ? 40c 2/4 2016.09 - rev.a www.rohm.com ? 2015 rohm co., ltd. all rights reserved. data sheet
RR1VWM6S ? electrical characteristic curves 1 10 100 1000 0.001 0.01 0.1 1 10 100 1000 r th (j-a) r th (j-l) 0.1 1 10 100 110100 t j = 25 c i fsm time transient thermal impedance : r th ( c/w) peak surge forward current : i fsm (a) time : t(ms) i fsm -t characteristics time : t(s) r th -t characteristics average rectified forward current : i o (a) ambient temperature : t a ( c) derating curve (i o -t a ) average rectified forward current : i o (a) lead temperature : t l ( c) derating curve (i o -t l ) 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 25 50 75 100 125 150 175 d = 0.1 d = 0.2 half sin wave d = 0.5 d.c. 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0 25 50 75 100 125 150 175 d.c. d = 0.1 d = 0.2 d = 0.5 half sin wave t t j =175 c d=t/t t v r io v r =v rmax 0a 0v t t j =175 c d=t/t t v r io v r =v rmax 0a 0v 50mm x 50mm x 0.8mm glass epoxy(fr-4) one side is all covered with copper (35um thickness) 3/4 2016.09 - rev.a www.rohm.com ? 2015 rohm co., ltd. all rights reserved. data sheet
RR1VWM6S ? electrical characteristic curves forward power dissipation : p f (w) average rectified forward current : i o (a) i o -p f characteristics 0.0 0.5 1.0 1.5 2.0 2.5 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 d = 0.1 d = 0.2 half sin wave d = 0.5 d.c. t j = 175 c 4/4 2016.09 - rev.a www.rohm.com ? 2015 rohm co., ltd. all rights reserved. data sheet
notice - p ga - e rev.00 3 ? 201 5 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our p roducts are designed and manufactured for application in ordinary electronic equipment s ( such as av equipment, oa equipment, telecommunication equipment, home elec tronic appliances, amusement equipment, etc.). if you intend to use our products in devices requiring extremely high reliability ( such as medical equipment ( n ote 1 ) , transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, f uel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life , bodily injury or serious damage to property ( specific applications ) , please consult with the rohm sales represe ntative in advance. unless otherwise agreed in writing by rohm in advance, rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any rohm s products for specific appl ications. ( n ote1) m edical e quipment c lassification of the s pecific applications japan usa eu china class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsi bilities, adequate safety measures including but not limited to fail - safe design against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our p roducts are designed and manufactured for use under standard conditions a nd not under any special or extraordinary environments or conditions, as exemplified below . accordingly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any rohms p roduct s under any special or extraordinary environments or conditions . if you intend to use our products under any special or extraordinary environments or conditions (as exemplified below), your independent v erification and confirmation of product performance, reliability, etc, pri or to use, must be necessary : [a] use of our products in any types of liquid, including water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the p roducts are exposed to direct sunlight or dust [c] use of our prod ucts in places where the p roducts are exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the p roducts are exposed to static electricity or electromagnetic waves [e] use of our products in p roximity to heat - producing components, plastic cords, or other flammable items [f] s ealing or coating our p roducts with resin or other coating materials [g] use of our products without cleaning residue of flux (even if you use no - clean type fluxes, cleanin g residue of flux is recommended); or washing our products by using water or water - soluble cleaning agents for cleaning residue after soldering [h] use of the p roducts in places subject to dew condensation 4 . the p roducts are not subject to radiation - proo f design . 5 . please verify and confirm characteristics of the final or mounted products in using the products. 6 . in particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of pe rformance characteristics after on - board mounting is strongly recommended. avoid applying power exceeding normal rated power; exceeding the power rating under steady - state loading condition may negatively affect product performance and reliability. 7 . de - rate power dissipation d epending on a mbient temperature . when used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8 . confirm that operation temperature is within the specified range described in the product specification. 9 . rohm shall not be in any way responsible or liable for f ailure induced under devian t condition from what is defined in this document . precaution for mounting / circuit board design 1. when a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used on a surface - mount products, the flow soldering method must be used on a through hole mount products. i f the flow soldering method is preferred on a surface - mount products , please consult with the roh m representative in advance. for details , please refer to rohm mounting specification
notice - p ga - e rev.00 3 ? 201 5 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, please allow a sufficient margin considerin g variations of the characteristics of the p roducts and external components, including transient characteristics, as well as static characteristics. 2. you agree that application notes, reference designs, and associated data and information contained in t his document are presented only as guidance for products use . therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in t his document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this p roduct is e lectrostatic sensitive product, which may be damaged due to e lectrostatic discharge. please take proper caution in your manufacturing process and stor age so that voltage exceeding the product s maximum rating will not be applied to p roducts. please take special care under dry condition (e .g. grounding of human body / equipment / solder iron, isolation from charged objects, setting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriorate if the p roducts are stored in the places where : [a] the p roducts are exposed to sea winds or corrosive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to direct sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage condition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm solderability before using p roducts of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the correct direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excess ive stress applied when dropping of a carton. 4. use p roducts within the specified time after opening a humidity barrier bag. baking is required before using p roducts of which storage time is exceeding the recommended storage time period . precaution for p roduct l abel a two - dimensional barcode printed on rohm p roduct s label is for rohm s internal use only . precaution for d isposition when disposing p roducts please dispose them properly using a n authorized industry waste company. precaution for foreign e xchange and foreign t rade act since concerned goods might be fallen under listed items of export control prescribed by foreign exchange and foreign trade act, please consult with rohm in case of export. precaution regarding intellectual property rights 1. all information an d data including but not limited to application example contained in this document is for reference only. rohm does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party reg arding such information or data. 2. rohm shall not have any obligations where the claims, actions or demands arising from the combination of the products with other articles such as components, circuits, systems or external equipment (including software). 3. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the products or the information contained in this document. provided, however, that rohm will not assert it s intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the products, subject to the terms and conditions herein. other precaution 1. this document may not be reprinted or reproduced, in whole or in part, without prior written consent of rohm. 2. the products may not be disassemble d, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. i n no event shall you use in any way whatso ever the products and the related technical information contained in the products or this document for any military purposes , including but not limited to, the development of mass - destruction weapons . 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties.
datasheet part number RR1VWM6S package pmde unit quantity 3000 minimum package quantity 3000 packing type taping constitution materials list inquiry rohs yes RR1VWM6S - web page distribution inventory
|
