View B154PW01-V1_7874787.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

au optronics corporation product specification document version 0.3 1/1 ( v ) preliminary specifications ( ) final specifications module 15.4? wxga+ color tft-lcd model name b154pw01 v1 customer date checked & approved by note: this specification is subject to change without notice. approved by date prepared by mdbu marketing division / au optronics corporation www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 2/2 contents 1. handling precautions ........................................................................................................ ...... 4 2. general description......................................................................................................... ........ 4 2.1 general specification ...................................................................................................... ... 5 2.2 optical characteristics .................................................................................................... ... 5 3. functional block diagram.................................................................................................... .11 4. absolute maximum ratings.................................................................................................. 12 4.1 absolute ratings of tft lcd module.............................................................................. 12 4.2 absolute ratings of backlight unit ................................................................................... 12 4.3 absolute ratings of environment ..................................................................................... 12 5. electrical characteristics.................................................................................................. ..... 13 5.1 tft lcd module............................................................................................................. . 13 5.2 backlight unit ............................................................................................................. ...... 15 6. signal characteristic ....................................................................................................... ...... 17 6.1 pixel format image......................................................................................................... . 17 6.2 the input data format ...................................................................................................... . 18 6.3 signal description/pin assignment .................................................................................. 19 6.4 interface timing ........................................................................................................... .... 21 7. connector description ....................................................................................................... ... 24 7.1 tft lcd module............................................................................................................. . 24 7.2 backlight unit ............................................................................................................. ...... 24 7.3 signal for lamp connector ............................................................................................... 24 8. vibration and shock test (stand alone) .............................................................................. 25 8.1 vibration test ............................................................................................................. ...... 25 8.2 shock test spec: ........................................................................................................... .. 25 9. reliability................................................................................................................. ............... 26 10. mechanical characteristics................................................................................................. 27 10.1 lcm outline dimension ................................................................................................. 27 11.1 shipping label format ................................................................................................... 29 11.2. carton package........................................................................................................... .. 30 11.3 shipping package of palletizing sequence ..................................................................... 30 12. appendix: edid description ............................................................................................. 31 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 3/3 record of revision version and date page old description new description remark 0.1 2005/12/01 all first edition for customer 0.2 2006/02/06 31 add edid description 0.3 2006/03/10 29 hw: 1a hw:0a www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 4/4 1. handling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the ccfl reflector edge. instead, press at the far ends of the cfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an enclosure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammability grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source(, iec60950 or ul1950), or be applied exemption. 14) the lcd module is designed so that the ccfl in it is supplied by limited current circuit(iec60950 or ul1950). do not connect the ccfl in hazardous voltage circuit. 2. general description b154pw01 v1 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the wxga+ (1440(h) x 900(v)) screen and 262k colors (rgb 6-bits data driver). all input si gnals are lvds interface compatible. inverter of backlight is not included. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 5/5 b154pw01 v1 is designed for a display unit of notebook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 j condition: items unit specifications screen diagonal [mm] 391 (15.4w?) active area [mm] 331.2 x 207.0 pixels h x v 1440x3(rgb) x 900 pixel pitch [mm] 0.23025x0.23025 pixel arrangement r.g.b. vertical stripe display mode normally white white luminance (i ccfl =6.0ma) note: i ccfl is lamp current [cd/m 2 ] 300 typ. (5 points average) 275 min. (5 points average) ( note1 ) luminance uniformity 1.25 max. (5 points) contrast ratio 400 typ optical rise time/fall time [msec] 4/12 typ. nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 6.0 max.(without inverter) weight [grams] 535 max. physical size [mm] 344.0 typ. x 222.0 typ. x 6.1 max. electrical interface 2 channel lvds surface treatment anti-glare, hardness 3h, reflectance 4.3% support color 262k colors ( rgb 6-bit ) temperature range operating storage (non-operating) [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance 2.2 optical characteristics the optical characteristics are measured under stable conditions at 25 j (room temperature): www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 6/6 item unit conditions min. typ. max. note white luminance i ccfl =6.0ma [cd/m 2 ] 5 points average 275 300 - 1, 4, 5. [degree] [degree] horizontal (right) cr = 10 (left) 60 60 70 70 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) 50 50 60 60 - - 9 luminance uniformity 5 points 1.25 1 luminance uniformity 13 points 1.50 2 cr: contrast ratio 300 400 - 6 cross talk % 4 7 [msec] rising - 4 8 [msec] falling - 12 17 response time [msec] rising + falling 16 25 8 red x 0.560 0.590 0.620 red y 0.315 0.345 0.375 green x 0.285 0.315 0.345 green y 0.520 0.555 0.580 blue x 0.125 0.155 0.185 blue y 0.115 0.145 0.175 white x 0.290 0.313 0.343 color / chromaticity coordinates (cie 1931) white y 0.299 0.329 0.350 2,8 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 7/7 note 1: 5 points position (display area : 331.2mm x 207.0mm) 1 2 3 4 5 h/4 h/4 h/4 h/4 h w w/4 w/4 w/4 w/4 note 2: 13 points position w/4 w w/4 h h/4 h/4 h/4 h/4 7 9 10 w/4 1 8 w/4 10 10 10 10 2 3 13 12 45 6 11 note 3: the luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the minimum test point luminance note 4: measurement method _ w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points _ w5 = minimum brightness of five points www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 8/8 the lcd module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measur ement should be executed after lighting backlight for 30 minutes in a stable, windless and dark room. note 5 ?g definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points ?a y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the point x at figure in note (1). note 6 ?g definition of contrast ratio: contrast ratio is calculated with the following formula. note 7 ?g definition of cross talk (ct) ct = | y b ? y a | / y a ?? 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd module 50 cm photo detector lcd panel field=2 x contrast ratio ( cr ) = bri g htness on the ?white? state bri g htness on the ?black? state www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 9/9 y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8: definition of response time: the output signals of bm-7 or equivalent are measured when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising time), respectively. th e response time interval between the 10% and 90% of amplitudes. refer to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 10/10 note 9. definition of viewing angle viewing angle is the measurement of contrast ratio ? 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( c ) horizontal left and right and 90 ( x ) vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 11/11 3. functional block diagram the following diagram shows the functional block of the 15.4wxga+ tft/lcd module: www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 12/12 4. absolute maximum ratings absolute maximum ratings of the module is as following: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive voltage vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions ccfl current iccfl - 6.5 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 3 operation humidity hop -- 95 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: at ta (25 j ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to auo iis(incoming inspection standard). twb=39c operating range storage range www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 13/13 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive volta g e 3.0 3.3 3.6 [volt] pdd vdd power 1.7 [watt] note 1 idd idd current 400 500 [ma] note 1 i rush inrush current 2000 [ma] note 2 vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p note 1 : maximum measurement condition ?g black patterm note 2 ?g measure condition +5.0v +12.0v vcc r1 47k r2 1k vr1 47k sw1 sw mag-spst 1 2 f1 q3 ao6402 g d2 s d1 d5 d6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) 90% 10% vin rising time 0v 3.3v 0.5ms www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 14/14 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. it is recommended to refer the specifications of thc63lvdf84a(thine electronics inc.) in detail. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform vth vtl vcm v ss www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 15/15 5.2 backlight unit parameter guideline for ccfl inverter parameter min typ max units condition white luminance 5 points average 275 300 - [cd/m 2 ] (ta = 25 j ) ccfl current(i ccfl ) 2.0 6.0 7.0 [ma] rms (ta=25 j ) note 2 ccfl frequency(f ccfl ) 45 52 65 [khz] (ta=25 j ) note 3,4 ccfl ignition voltage(vs) 1340 [volt] rms (ta= 0 j ) note 5 ccfl ignition voltage(vs) 1030 [volt] rms (ta= 25 j ) note 5 ccfl voltage (reference) (v ccfl ) 620 720 910 [volt] rms (ta=25 j ) note 6 ccfl power consumption (p ccfl ) - 4.30 4.70 [watt] (ta=25 j ) note 6 note 1: typ are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to chec k safety circuit very carefully. impedance of ccfl, for instance, becomes more than 1 [m ohm] when cfl is damaged. *4 generally, ccfl has some amount of delay time after applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until discharge. *5 ccfl discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the screen. *6 reducing ccfl current increases ccfl discharge voltage and generally increases ccfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2: it should be employed the inverter which has ?duty dimming?, if iccfl is less than 4ma. note 3: ccfl discharge frequency should be carefully determined to avoid interference between inverter and tft lcd. note 4: the frequency range w ill not affect to lamp life and reliability characteristics. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 16/16 note 5: ccfl inverter should be able to give out a power that has a generating capacity of over 1,340 voltage. lamp units need 1,300 voltage minimum for ignition. note 6: calculator value for reference (i ccfl v ccfl =p ccfl ) note 7: requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. it shall help increase the lamp lif etime and reduce leakage current. a. the asymmetry rate of the inverter waveform should be less than 10%. b. the distortion rate of the waveform should bewithin ?? 2 ? 10%. * inverter output waveform had better be more similar to ideal sine wave. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 17/17 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 1 2 1439 1440 1st line 900th line www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 18/18 6.2 the input data format signal name description v edid +3.3v edid power clk edid edid clock input data edid edid data input orxin0-, orxin0+ odd lvds differential data input(ored0-ored5, ogreen0) orxin1-, orxin1+ odd lvds differential data input(ogreen1-ogreen5, oblue0-oblue1) orxin2-, orxin2+ odd lvds differential data input(o blue2-oblue5, hsync, vsync, de) orxclkin-, orxclkin+ odd lvds differential clock input erxin0-, erxin0+ even lvds differential data input(ered0-ered5, egreen0) erxin1-, erxin1+ even lvds differential data input(egreen1-egreen5, eblue0-eblue1) erxin2-, erxin2+ even lvds differential data input(eblue2-eblue5) erxclkin-, erxclkin+ even lvds differential clock input vdd +3.3v power supply gnd ground note: output signals from any system shall be low or high-impedance state when vdd is off. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 19/19 6.3 signal description/pin assignment lvds is a differential signal technology for l cd interface and high speed data transfer device. pin # signal name description 1 vss power ground 2 vdd + 3.3v power supply 3 vdd + 3.3v power supply 4 v edid + 3.3v edid power 5 aging aging mode power supply 6 clk edid edid clock input 7 data edid edid data input 8 odd_rin0- -lvds differential data input 9 odd_rin0+ +lvds differential data input 10 vss power ground 11 odd_rin1- -lvds differential data input 12 odd_rin1+ +lvds differential data input 13 vss power ground 14 odd_rin2- -lvds differential data input 15 odd_rin2+ +lvds differential data input 16 vss power ground 17 odd_clkin- -lvds differential clock input 18 odd_clkin+ +lvds differential clock input 19 vss power ground 20 even_rin0- -lvds differential data input 21 even_rin0+ +lvds differential data input 22 vss power ground 23 even_rin1- -lvds differential data input 24 even_rin1+ +lvds differential data input 25 vss power ground 26 even_rin2- -lvds differential data input 27 even_rin2+ +lvds differential data input 28 vss power ground 29 even_clkin- -lvds differential clock input 30 even_clkin+ +lvds differential clock input www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 20/20 note1: start from right side 30 1 nc gnd connecto r www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 21/21 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1440x900 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 50 60 - hz clock frequency 1/ t clock 50 48.2 60.2 mhz period t v 904 912 2048 active t vd 900 900 900 vertical section blanking t vb 4 12 - t line period t h 760 880 1024 active t hd 720 720 720 horizontal section blanking t hb 40 160 - t clock note : de mode only www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 22/22 6.4.2 timing diagram www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 23/23 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z st ate or low level when vdd is off. power sequence timing value parameter min. typ. max. units t1 0.5 - 10 (ms) t2 5 - 50 (ms) t3 0.5 - 50 (ms) t4 400 - - (ms) t5 200 - - (ms) t6 200 - - (ms) t7 0 - 10 (ms) t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t6 t7 power supply vdd lvds interface backlight on www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 24/24 7. connector description physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer jae or compatible type / part number fi-xb 30sl-hf10 or compatible mating housing/part number fi-x30h or compatible 7.2 backlight unit physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 25/25 8. vibration and shock test (stand alone) 8.1 vibration test test spec: test method: non-operation acceleration: 1.5g frequency: 26 - 500hz random sweep: 30 minutes each axis (x, y, z) 8.2 shock test spec: test spec: test method: non-operation acceleration: 260 g , half sine wave active time: 2 ms pulse: x,y,z .one time for each side www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation product specification document version 0.3 26/26 9. reliability items required condition note temperature humidity bias 40 j /95%,300hrs high temperature operation 50 j /dry,300hrs low temperature operation 0 j ,300hrs on/off test 25 j ,150hrs(on/30 sec. off/30sec., 10,000 cycles) hot storage 65 j /20% rh ,300 hours cold storage -25 j /50% rh ,300 hours thermal shock test -25 j /30 min ,65 j /30 min 100cycles non-op shock test (non-operating) 260g, 2ms, half-sine wave, +/- x, y,z direction,1 cycle vibration test (non-operating) sinusoidal vibration, 3.0 g zero-to-peak, 10 to 150 hz, 30 mins in each of three mutually perpendicular axes. esd contact : ? 8kv/ operation air : ? 15kv / operation note 1 image sticking 10x10 checker pattern, 10 hrs, 25 j . the persisting pattern should be disappeared in 5 minutes note1: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 27/27 10. mechanical characteristics 10.1 lcm outline dimension www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 28/28 www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 29/29 11. shipping and package 11.1 shipping label format b154ew01 v4 3 a 3 axxg b154ew01 v4 3 a ratin g :7.5 v ; 800ma b154pw01 v1 0 a model name week code xxxxxxxxxxxxxxx 0 a xxg www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 30/30 11.2. carton package the outside dimension of carton is 455 (l)mm x 380 (w)mm x 355 (h)mm 11.3 shipping package of palletizing sequence top cardboard wooden pallet bottom cardboard corner angle stretch film pe band note : limit of box palletizing = max 3 layers(ship and stock co nditions) www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 31/31 12. appendix: edid description address function value value value notes hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii 10 00010000 16 0a product code 60 01100000 96 0b hex, lsb first 9c 10011100 156 0c 32-bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 04 00000100 4 week 4 11 year of manufacture 10 00010000 16 2006 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input definition 80 10000000 128 15 max h image size 22 00100010 34 34cm 16 max v image size 16 00010110 22 22cm 17 display gamma 78 01111000 120 gamma 2.2 18 feature support 0a 00001010 10 19 red/green low bits 1c 00011100 28 1a blue/white low bits f5 11110101 245 1b red x/ high bits 97 10010111 151 1c red y 58 01011000 88 1d green x 50 01010000 80 1e green y 8e 10001110 142 1f blue x 27 00100111 39 20 blue y 27 00100111 39 21 white x 50 01010000 80 www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 32/32 22 white y 54 01010100 84 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 established timing 3 00 00000000 0 26 standard timing #1 01 00000001 1 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 detailed timing/monitor 9f 10011111 159 37 descriptor #1 25 00100101 37 38 a0 10100000 160 39 40 01000000 64 3a 51 01010001 81 3b 84 10000100 132 3c 0c 00001100 12 3d 30 00110000 48 3e 40 01000000 64 3f 20 00100000 32 40 33 00110011 51 41 00 00000000 0 42 4b 01001011 75 43 cf 11001111 207 44 10 00010000 16 45 00 00000000 0 46 00 00000000 0 www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 33/33 47 19 00011001 25 48 detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 01 00000001 1 4c 00 00000000 0 4d 06 00000110 6 4e 10 00010000 16 4f 30 00110000 48 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 0a 00001010 10 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 ascii data string 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f 42 01000010 66 60 31 00110001 49 61 35 00110101 53 62 34 00110100 52 63 50 01010000 80 64 57 01010111 87 65 30 00110000 48 66 31 00110001 49 67 20 00100000 32 68 56 01010110 86 69 30 00110000 48 6a 0a 00001010 10 www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 34/34 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 monitor name: color lcd 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fc 11111100 252 70 00 00000000 0 71 43 01000011 67 c 72 6f 01101111 111 o 73 6c 01101100 108 l 74 6f 01101111 111 o 75 72 01110010 114 r 76 20 00100000 32 77 4c 01001100 76 l 78 43 01000011 67 c 79 44 01000100 68 d 7a 0a 00001010 10 7b 20 00100000 32 7c 20 00100000 32 7d 20 00100000 32 7e extension flag 00 00000000 0 7f checksum bc 10111100 188 www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 35/35 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of B154PW01-V1

	To Download B154PW01-V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .