g do not scale from this print g ipd1-xx-d-x no of positions -02 thru -25 (per row) [see fig. 2 for -02 position] row specification -d: double -p: polarized (not available with -k option) (leave blank for no polarization) (see fig. 3) *-k: keyed polarization (not available with -p option) (see sheet 2, fig. 4) polarization option *not released for production .250 .002 .350 .050 (typ) .0775 (4 plcs) ((no of positions -1) x .100) .100 "a" "a" 'a' 'b' 'c' c3 c4 02 01 07 .002 .003 ((no of positions x .100) + .055) .050 .220 .505 - .000 + .005 .035 .010 .078 .010 .08 c1 c2 see note 11 .007 .003 .255 .4800 .0020 .059 - .001 + .002 .100 .005 .0723 (see note 14) "b" "b" 'd' 'h' section "a"-"a" c5 see note 8 see note 2 see note 3 c6 .050 (typ) .050 .020 (2 plcs) 'g' 01 07 08 05 06 11 12 see note 12 04 03 02 .045 .112 .082 .0923 (see note 14) 'f' 'e' section "b"-"b" parting line gate pads (see note 9) "j" "j" 02 01 07 ipd1-06-d-p shown (same as fig. 1, except as shown) fig. 3 .255 section "j"-"j" c fig. 1 ipd1-06-d shown sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .003 [.08] .xxxx: .0015 [.038] material: .100 shrouded contact body by: ipd1-xx-d-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing chad f 03/05/2002 2 1 sheet scale: 2:1 zytel 103fhs, color: white c:\enterprisevault\dwg\misc\mktg\ipd1-xx-d-x-mkt.slddrw max regrind: 25% max flash allowed: .004 max gate vestige: .002 notes: 1. represents a critical dimension. 2. samtec logo shall appear at one location on surface shown, approximately .150 x .094 (both sides). 3. all multiple cavity molds shall identify each cavity with a letter designation located where shown. 4. all identification marks must not stand greater than .002 off the surface of the part. 5. molded surfaces shall be consistent and smooth. surfaces to be free of scatches, nicks, sink areas, voids or other blemishes. 6. max allowable bow: see table 1. bow to be measured at midline of part. 7. part to be symmetric about the centerline within +/-.002, unless otherwise stated. 8. number of positions (per row) to be shown in this area excluding 2, 3 and 4 positions. size and depth similar to position 1 indicator. 9. gate pads must be recessed .005. 10. end cores are polarized. confirm geometry relative to position 1 indicator & gate pads. 11. position 1 indicator to be raised .005 max, not present on 2 position option. 12. specified positions to be identified where shown (note 4 applies). 13. mold designer has discretion over rib location. steel print setup sheet must show rib configuration for each part number. 14. part must draft inward from bottom to top of stack. 15. all dimensions to be symmetric about centerline within .0015 unless otherwise stated. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision g
.060 .075 .002 .145 .002 .035 .085 .145 .225 .005 r .025 detail 'a' scale 3 : 1 c8 c7 .0800 (typ) .030 .1000 (typ) detail 'b' scale 5 : 1 c9 c10 .0310 sq (typ) .100 ref .0400 (typ) .0400 (typ) .0305 (typ) detail 'c' scale 5 : 1 c11 .0200 18 (typ) .0187 15 (typ) detail 'd' scale 5 : 1 .030 .076 .110 - .003 + .000 34 .4550 .250 r .025 (typ) .041 .005 .015 20 .200 .105 - .003 + .001 .068 detail 'f' scale 4 : 1 c14 .0850 - .000 + .003 (typ) .0895 - .0000 + .0030 .0750 - .000 + .003 (typ) detail 'g' scale 5 : 1 .0100 30 (typ) .0735 .069 - .001 + .002 .135 .1300 .0250 .005 .0020 .0100 15 (typ) 2 ref 30 detail 'e' scale 8 : 1 c13 c12 fig. 2 -02 position (same as fig. 1, unless otherwise stated) .325 .020 (typ) .006 (typ) detail 'h' scale 12 : 1 g "n" "n" fig. 4 -k: keyed polarization ( ipd1-06-d-k shown) (same as fig. 1, unless otherwise stated) not released for production .031 .0300 2 section "n"-"n" scale 4 : 1 sheet of .100 shrouded contact body by: ipd1-xx-d-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing chad f 03/05/2002 2 2 sheet scale: 2:1 revision g c:\enterprisevault\dwg\misc\mktg\ipd1-xx-d-x-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
