View SIT9102_7686902.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sitime corporation 990 almanor avenue sunnyvale, ca 94085 (408) 328-4400 www.sitime.com rev. 1.52 revised june 23, 2010 SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator features ? extremely low rms phase jitter (random) ? <1 ps (typical) ? wide frequency range ? 1 mhz to 220 mhz ? 220 mhz to 800 mhz refer to sit9107 ? high frequency stability ? 10 ppm, 15 ppm, 20 ppm ? 25 ppm, 50 ppm ? operating voltage ? 1.8, 2.5 or 3.3 v ? other voltages up to 3.63 v (contact sitime) ? operating temperature range ? industrial, -40 to 85 c ? extended commercial, -20 to 70 c ? commercial, 0 to 70 c ? small footprint ? 5.0 x 3.2 x 0.75 mm ? 7.0 x 5.0 x 0.90 mm ? pb-free and rohs compliant ? for spread spectrum see sit9002 ? ultra-reliable start up and greater immunity from inter ference benefits ? ultra fast lead time: 2 to 3 weeks ? no crystal or capacitors required ? eliminates crystal qualification time ? 50% + board saving space ? more cost effective than quartz oscillators, quartz crystals and clock ics. ? completely quartz-free applications ? server ? router ?raid controller ? gigabit ethernet ? 10 gigabit ethernet ? fiber channel ?sata / sas ? pci-express ? fully buffered dimm ? system clock ? networking and computing block diagram pinout 1 6 5 4 2 3 vdd out- out+ nc gnd st/oe high performance phase lock loop mems resonator st/oe gnd vdd out- out+
rev. 1.52 page 2 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator absolute maximum ratings attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. actual performance of the ic is only guarante ed within the operational specifications, not at absolute maximum ratings. pin description pin no. name pin description 1st /oe input standby or output enable pin for out+ and out-. oe: when high or open : out+ and out- = active when low : out+ and out- = high impedance state st: when high or open : out+ and out- = active when low : out+ and out- = output is low (weak pull down), oscillation stops 2 nc na do not connect pin, leave it floating. 3 gnd power vdd power supply ground. connect to ground 4 out+ output 1 to 220 mhz programmable clock output . 5 out- output 6 vdd power power supply ab solute maximum table parameter min. max. unit storage temperature -65 150 c vdd -0.5 4 v vin gnd - 0.5 vdd + 0.5 v theta ja ( with copper plane on vdd and gnd) 5.0 x 3.2 package 7.0 x 5.0 package when center pad is soldered down 7.0 x 5.0 package when center pad is not soldered down ?68c/w ?38c/w ?90c/w theta jc (with pcb traces of 0.010 inch to all pins) 5.0 x 3.2 package 7.0 x 5.0 package when center pad is soldered down 7.0 x 5.0 package when center pad is not soldered down ?45c/w ?35c/w ?48c/w soldering temperature (follow standard pb free soldering guidelines) ? 260 c number of program writes ? 1 na program retention over -40 to 125c, process, vdd (0 to 3.6v) ? 1,000+ years human body model (jesd22-a114) 2000 ? ? charged device model (jesd22-c101) 750 ? ? machine model (jesd22-a115) 200 ? ? environmental compliance parameter condition/test method mechanical shock mil-std-883f, method 2002 mechanical vibration mil-std-883f, method 2007 temperature cycle mil-std-883f, method 1010-65-150c (1000 cycle) solderability mil-std-883f, method 2003 moisture sensitivity level msl1 @ 260c
rev. 1.52 page 3 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator dc electrical specifications lvcmos input, oe or st pin, 3.3v 10% or 2.5v 10% or 1.8v 5%, -40 to 85c symbol parameter condition min. typ. max. unit v ih input high voltage 70 ? ? %vdd v il input low voltage ? ? 30 %vdd i ih input high current oe or st pin ? ? 10 a i il input low current oe or st pin -10 ? ? a t pu power up time time from minimum power supply voltage to the first cycle (guaranteed no runt pulses) ??10ms lvpecl, 3.3v 10% or 2.5v 10%, -40 to 85c symbol parameter condition min. typ. max. unit v dd supply voltage 2.97 3.3 3.63 v 2.25 2.5 2.75 v i dd supply current v dd = 3.3, excluding load termination current ? 68 74 ma v dd = 2.5, excluding load termination current ? 65 71 ma v oh output high voltage 50 ohm termination to v dd - 2.0v see figure 2, 3. v dd -1.1 ? v dd -0.7 v v ol output low voltage v dd -2.0 ? v dd -1.4 v v swing pk-pk output voltage swing 600 800 1000 mv hcsl, 3.3v 10% or 2.5v 10%, -40 to 85c symbol parameter condition min. typ. max. unit v dd supply voltage 2.97 3.3 3.63 v 2.25 2.5 2.75 v i dd supply current v dd = 3.3, excluding load termination current ? 65 70 ma v dd = 2.5, excluding load termination current ? 62 67 ma v oh output high voltage 50 ohm termination to gnd see figure 4. 600 ? 950 mv v ol output low voltage 0.0 ? 50 mv v swing pk-pk output voltage swing 600 ? 950 mv lvds, 3.3v 10% or 2.5v 10%, -40 to 85c symbol parameter condition min. typ. max. unit v dd supply voltage 2.97 3.3 3.63 v 2.25 2.5 2.75 v i dd supply current v dd = 3.3, excluding load termination current ? 73 79 ma v dd = 2.5, excluding load termination current ? 70 76 ma v od1 differential output voltage swing mode = normal single load termination. see figure 5. 250 350 450 mv v od1 v od magnitude change ? ? 50 mv v os1 offset voltage ? 1.2 ? v v os1 v os magnitude change ? ? 50 mv v od2 differential output voltage swing mode = high single load termination. see figure 5. 500 700 900 mv v od2 v od magnitude change ? ? 50 mv v os2 offset voltage ? 1.2 ? v v os2 v os magnitude change ? ? 50 mv v od3 differential output voltage swing mode = high double load termination. see figure 6. 250 350 450 mv v od3 v od magnitude change ? ? 50 mv v os3 offset voltage ? 1.2 ? v v os3 v os magnitude change ? ? 50 mv
rev. 1.52 page 4 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator ac electrical specifications cml, 3.3v 10% or 2.5v 10% or 1.8v 5%, -40 to 85c symbol parameter condition min. typ. max. unit v dd supply voltage 2.97 3.3 3.63 v 2.25 2.5 2.75 v 1.71 1.8 1.89 v i dd supply current v dd = 3.3v excluding load termination current ?4851ma v dd = 2.5v ? 47 50 ma v dd = 1.8v ? 38 41 ma v oh1 output high voltage swing mode = normal single load termination see figure 7. v dd -0.1 ? v dd v v ol1 output low voltage v dd -0.55 v dd -0.425 v dd -0.3 v v swing1 pk-pk output voltage swing 300 425 550 mv v oh2 output high voltage swing mode = high single load termination see figure 7. v dd -0.1 ? v dd v v ol2 output low voltage v dd -1.1 v dd -0.85 v dd -0.6 v v swing2 pk-pk output voltage swing 600 850 1100 mv v oh3 output high voltage swing mode = high double load termination see figure 8. v dd -0.1 ? v dd v v ol3 output low voltage v dd -0.55 v dd -0.425 v dd -0.3 v v swing3 pk-pk output voltage swing 300 425 550 mv lvpecl, 3.3v 10%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 1.0 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -10 ? +10 ppm -20 to 70c -40 to 85c -15 ? +15 ppm -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 100 150 300 ps ph j rms phase jitter (random) f out = 106.25 mhz @ bw: 637 khz to10 mhz ? 1.6 ? ps f out = 156.25 mhz @ bw: 1.875 to 20 mhz ? 0.5 ? ps f out = 200 mhz @ bw: 1 to 20 mhz ? 0.7 ? ps p j rms period jitter f out = 106.25 mhz ? 1.8 2.3 ps f out = 156.25 mhz ? 1.3 1.8 ps f out = 200 mhz ? 1.3 1.8 ps
rev. 1.52 page 5 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator lvpecl, 2.5v 10%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 1.0 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -10 ? +10 ppm -20 to 70c -40 to 85c -15 ? +15 ppm -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 100 150 300 ps ph j rms phase jitter (random) f out = 106.25 mhz @ bw: 637 khz to10 mhz ? 1.6 ? ps f out = 156.25 mhz @ bw: 1.875 to 20 mhz ? 0.5 ? ps f out = 200 mhz @ bw: 1 to 20 mhz ? 0.7 ? ps p j rms period jitter f out = 106.25 mhz ? 1.8 2.3 ps f out = 156.25 mhz ? 1.3 1.8 ps f out = 200 mhz ? 1.3 1.8 ps hcsl, 3.3v 10%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 1.0 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -10 ? +10 ppm -20 to 70c -40 to 85c -15 ? +15 ppm -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 200 280 375 ps ph j rms phase jitter (random) f out = 100 mhz @ bw: 1.5 mhz to 22 mhz ? 0.8 ? ps f out = 200 mhz @ bw: 1.5 mhz to 22 mhz ? 0.4 ? ps p j rms period jitter f out = 100 mhz ? 1.6 2.2 ps f out = 200 mhz ? 1.5 1.9 ps
rev. 1.52 page 6 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator hcsl, 2.5v 10%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 1.0 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -10 ? +10 ppm -20 to 70c -40 to 85c -15 ? +15 ppm -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 200 300 400 ps ph j rms phase jitter (random) f out = 100 mhz @ bw: 1.5 mhz to 22 mhz ? 0.8 ? ps f out = 200 mhz @ bw: 1.5 mhz to 22 mhz ? 0.4 ? ps p j rms period jitter f out = 100 mhz ? 1.6 2.2 ps f out = 200 mhz ? 1.5 2.1 ps lvds, 3.3v 10%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 10 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -10 ? +10 ppm -20 to 70c -40 to 85c -15 ? +15 ppm -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 100 200 325 ps ph j rms phase jitter (random) f out = 106.25 mhz @ bw: 637 khz to10 mhz ? 1.7 ? ps f out = 156.25 mhz @ bw: 1.875 to 20 mhz ? 0.7 ? ps f out = 200 mhz @ bw: 1 to 20 mhz ? 0.7 ? ps p j rms period jitter f out = 106.25 mhz ? 2.0 2.7 ps f out = 156.25 mhz ? 1.8 2.5 ps f out = 200 mhz ? 1.8 2.5 ps
rev. 1.52 page 7 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator lvds, 2.5v 10%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 1.0 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -10 ? +10 ppm -20 to 70c -40 to 85c -15 ? +15 ppm -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 100 260 325 ps ph j rms phase jitter (random) f out = 106.25 mhz @ bw: 637 khz to10 mhz ? 1.7 ? ps f out = 156.25 mhz @ bw: 1.875 to 20 mhz ? 0.7 ? ps f out = 200 mhz @ bw: 1 to 20 mhz ? 0.7 ? ps p j rms period jitter f out = 106.25 mhz ? 2.5 3.3 ps f out = 156.25 mhz ? 2.4 3.5 ps f out = 200 mhz ? 2.4 3.5 ps cml, 3.3v 10%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 1.0 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -10 ? +10 ppm -20 to 70c -40 to 85c -15 ? +15 ppm -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 150 220 300 ps ph j rms phase jitter (random) f out = 106.25 mhz @ bw: 637 khz to10 mhz ? 1.6 ? ps f out = 156.25 mhz @ bw: 1.875 to 20 mhz ? 0.6 ? ps f out = 200 mhz @ bw: 1 to 20 mhz ? 0.8 ? ps p j rms period jitter f out = 106.25 mhz ? 2 2.5 ps f out = 156.25 mhz ? 1.9 2.5 ps f out = 200 mhz ? 1.9 2.4 ps
rev. 1.52 page 8 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator cml, 2.5v 10%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 1.0 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -10 ? +10 ppm -20 to 70c -40 to 85c -15 ? +15 ppm -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 150 230 300 ps ph j rms phase jitter (random) f out = 106.25 mhz @ bw: 637 khz to10 mhz ? 1.6 ? ps f out = 156.25 mhz @ bw: 1.875 to 20 mhz ? 0.6 ? ps f out = 200 mhz @ bw: 1 to 20 mhz ? 0.8 ? ps p j rms period jitter f out = 106.25 mhz ? 2.1 2.5 ps f out = 156.25 mhz ? 1.9 2.5 ps f out = 200 mhz ? 1.9 2.5 ps cml, 1.8v 5%, -40 to 85c symbol parameter condition min. typ. max. unit f out output frequency 1.0 ? 220 mhz f stab frequency stability inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70c -15 ? +15 ppm -20 to 70c -40 to 85c -20 ? +20 ppm -25 +25 ppm -50 +50 ppm f age aging first year @ 25c ? ? 1 ppm dc duty cycle 45 ? 55 % t r /t f output rise/fall time 20% to 80% 150 240 325 ps ph j rms phase jitter (random) f out = 106.25 mhz @ bw: 637 khz to10 mhz ? 1.7 ? ps f out = 156.25 mhz @ bw: 1.87 to 20 mhz ? 0.6 ? ps f out = 200 mhz @ bw: 1 to 20 mhz ? 0.8 ? ps p j rms period jitter f out = 106.25 mhz ? 2.3 2.9 ps f out = 156.25 mhz ? 2.1 2.7 ps f out = 200 mhz ? 2.1 2.7 ps
rev. 1.52 page 9 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator termination diagrams figure 1. lvpecl ac coupled typical termination d+ d- out+ out- drive device receiver device SIT9102, lvpecl-0 z0 = 50 ohm z0 = 50 ohm r1 50 ohm 50 ohm r1 vtt 100 nf 100 nf vdd = 3.3v r1 = 150 ohm vdd = 2.5v r1 = 120 ohm z0 = 50ohm z0 = 50ohm d+ d- out+ out- 50ohm vtt = vdd ? 2.0 v drive device receiver device SIT9102, lvpecl-1 50ohm figure 2. lvpecl dc coupled typical termination with termination voltage figure 3. lvpecl dc coupled typical te rmination without te rmination voltage vdd = 3.3v r1 = r3 = 133 ohm r2 = r4 = 82 ohm vdd = 2.5v r1 = r3 = 250 ohm r2 = r4 = 62.5 ohm z0 = 50ohm z0 = 50ohm d+ d- out+ out- drive device receiver device r1 r2 r3 r4 vdd SIT9102, lvpecl-1
rev. 1.52 page 10 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator figure 4. hcsl typical termination rs = 10 ohm to 35 ohm d+ d- out+ out- drive device receiver device SIT9102 50 ohm z0 = 50 ohm z0 = 50 ohm rs rs 50 ohm note: 1. all the tests are done with rs = 20 ohm (recommended). z0 = 50 ohm z0 = 50 ohm d+ d- out+ out- 100 ohm drive device receiver device SIT9102 figure 5. lvds single termination (load terminated) figure 6. lvds double termination (source + load terminated) z0 = 50 ohm z0 = 50 ohm d+ d- out+ out- drive device receiver device SIT9102 100 ohm ab note: for ac coupled operation, include/insert decoupling caps at points a or b 100 ohm a b
rev. 1.52 page 11 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator z0 = 50 ohm z0 = 50 ohm d+ d- out+ out- 50 ohm vdd vt 3.63v drive device receiver device SIT9102 50 ohm < < figure 7. cml single load termination d+ d- out+ out- drive device receiver device SIT9102 vdd vt2 3.63v z0 = 50 ohm z0 = 50 ohm vdd vt1 3.63v 50 ohm 50 ohm 50 ohm 50 ohm ab notes: 1. for dc-coupled operation, vt1 = vt2 2. for ac coupled operation, include/insert decoupling caps at points a or b 2. for ac-coupled operation with capacitors placed at point a, vt2 sets the input common mode of receiver device and need not to be related to vt1 a b < < < < figure 8. cml double load termination
rev. 1.52 page 12 of 13 www.sitime.com SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator ordering information the part no. guide is for reference only. for real-time customization and exact part number, use the sitime part number generator . note: 1. without center pad. SIT9102ac - 132n33e123.12345t frequency 1.00000 to 220.00000 mhz part family ?SIT9102? revision letter ?a? is the revision of silicon temperature range ?i? industrial, -40 to 85oc packaging package size ?3? 5.0 x 3.2 mm ?4? 7.0 x 5.0 mm frequency stability ?f? for 10 ppm ?c? extended commercial, -20 to 70oc signalling type ?1? = lvpecl-1 (figure 2, 3) ?2? = lvds ?3? = cml ?4? = hcsl ?n? commercial, 0 to 70oc ?h? for 15 ppm ?1? for 20 ppm ?2? for 25 ppm ?3? for 50 ppm swing select ?n? = normal voltage supply ?18? for 1.8 v 5% (cml only) ?25? for 2.5 v 10% ?33? for 3.3 v 10% feature pin ?e? for output enable ?s? for standby ?0? = lvpecl-0 (figure 1) ?h? = high (lvds & cml only) ?t? for tape & reel (3 ku reel) ?y? for tape & reel (1 ku reel) blank for bulk ?8? 7.0 x 5.0 mm [1] frequency stability vs. temperature range options frequency stability (ppm) temperature range supply voltage 1.8 v 2.5 v 3.3 v 10 n (0 to +70c) ? 33 c (-20 to +70c) ? ?? i (-40 to +85c) ? ?? 15 n (0 to +70c) 3 33 c (-20 to +70c) ? 33 i (-40 to +85c) ? 33 20 n (0 to +70c) 3 33 c (-20 to +70c) 3 33 i (-40 to +85c) 3 33 25 n (0 to +70c) 3 33 c (-20 to +70c) 3 33 i (-40 to +85c) 3 33 50 n (0 to +70c) 3 33 c (-20 to +70c) 3 33 i (-40 to +85c) 3 33 signaling type vs. swing select options signaling type swing select supply voltage 1.8 v 2.5 v 3.3 v lvpecl-0 normal ? 33 high ? ?? lvpecl-1 normal ? 33 high ? ?? lvds normal ? 33 high ? 33 cml normal 3 33 high 3 33 hcsl normal ? 33 high ? ??
rev. 1.52 page 13 of 13 revised june 23, 2010 ? sitime corporation 2010. the information contained herein is subject to change at any time without notice. sitime assumes no responsibility or liability for any loss, damage or defect of a product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a sitime product, (ii) misuse or abuse including static discharge, neglect or accident, (iii) unauthorized modification or repairs which have been soldered or altered during assembly and are not capable of being tested by sitime under its normal test conditions, or (iv) improper installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electri cal stress. disclaimer: sitime makes no warranty of any kind, express or implied, with regard to this material, and specifically disclaims any and al l express or implied warranties, either in fact or by operation of law, statutory or otherwise, including the implie d warranties of merchantability and fitness for use or a particul ar purpose, and any implied warranty arising from course of dealing or usage of trade, as well as any common-law duties relating to accuracy or lack of negligence, with respect to this material, any sitime product and any product documentation. products sold by sitme are not suitable or intended to be used in a life support application or component, to operate nuclear facilities, or in other mission critical applications where human life may be involved or at stake. all sales are made conditioned upon compliance with the critical uses policy set forth below. critical use exclusion policy buyer agrees not to use sitime's products for any application or in any components used in life support devices or to operate n uclear facilities or for use in other mission-critical applications or components where human life or property may be at stake. sitime owns all rights, title and interest to the intellectual property related to sitime's products, including any software, f irmware, copyright, patent, or trademark. the sale of sitime products does not convey or imply any license under patent or other rights. sitime retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by sitime. unless otherwise agreed to in writing by sitime, any reproduction, modification, t ranslation, compilation, or representation of this material shall be strictly prohibited. SIT9102 lvpecl / hcsl / lvds / cml 1 to 220 mhz high performance oscillator notes: 2. ?y? denotes manufacturing origin and ?xxxx? denotes manufacturing lot number. the value of ?y? depend on the assembly locatio n of the device. 3. a capacitor of value 0.1 f between vdd and gnd is recommended. 4. the 7050 package with part number designation "-8" has no center pad. package information [2] dimension (mm) land pattern [3] (recommended) (mm) 5.0 x 3.2 x 0.75mm 0.750.05 yxxxx 1.20 #2 #5 #2 #5 #1 #3 #4 #6 #1 #3 #4 #6 7.0 x 5.0 x 0.90mm 5.00.10 1.40 1.10 5.08 7.00.10 2.60 #1 #3 #6 #4 #1 #3 #6 #4 0.90 0.10 #2 #5 #2 #5 2.30 1.47 no connect or connect to gnd (recommended) yxxxx [4] 5.08 1.60 1.60 3.80 2.30 1.47

▲Up To Search▲

Price & Availability of SIT9102

	To Download SIT9102 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .