? semiconductor components industries, llc, 2009 october, 2009 ? rev. 12 1 publication order number: CS8363/d CS8363 3.3 v dual micropower regulator with enable and reset the CS8363 is a precision micropower dual voltage regulator with enable and reset . the 3.3 v standby output is accurate within ? 2%, +2.4% while supplying loads of 100 ma. quiescent current is low, typically 140 a with a 300 a load. the active reset output monitors the 3.3 v standby output and is low during power ? up and regulator dropout conditions. the reset circuit includes hysteresis and is guaranteed to operate correctly with 1.0 v on the standby output. the second output tracks the 3.3 v standby output through an external adjust lead, and can supply loads of 250 ma. the logic level lead enable is used to control this tracking regulator output. both outputs are protected against overvoltage, short circuit, reverse battery and overtemperature conditions. the robustness and low quiescent current of the CS8363 makes it not only well suited for automotive microprocessor applications, but for any battery powered microprocessor applications. features ? 2 regulated outputs ? standby output 3.3 v ? 2%, +2.4%; 100 ma ? adjustable tracking output; 250 ma ? operation down to v in = 4.5 v ? reset for v stby ? enable for v trk ? low quiescent current ? protection features ? independent thermal shutdown ? short circuit ? 60 v load dump ? reverse battery a = assembly location wl = wafer lot y = year ww = work week d 2 pak ? 7 dps suffix case 936ab marking diagram pin 1. v stby 2. v in 3. v trk 4. gnd 5. adj 6. enable 7. reset device package shipping ? ordering information* CS8363ydps7 d 2 pak ? 7 50 units/rail CS8363ydpsr7 d 2 pak ? 7 750 tape & reel http://onsemi.com ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our t ape and reel packaging specifications brochure, brd8011/d. 1 CS8363 awlyww 1
CS8363 http://onsemi.com 2 figure 1. block diagram. consult your local sales representative for positive enable option + ? v in overvoltage shutdown current limit bandgap current limit thermal shutdown ? + reset + ? gnd ? + ovsd tsd ovsd bg bg reset v stby 3.3 v, 100 ma, 2.0% v trk 250 ma v in adj tsd tsd ovsd v stby enable bg reset absolute maximum ratings* rating value unit supply voltage, v in ? 16 to 26 v positive transient input voltage, tr > 1.0 ms 60 v negative transient input voltage, t < 100 ms, 1.0 % duty cycle ? 50 v input voltage range (enable , reset ) ? 0.3 to 10 v junction temperature ? 40 to +150 c storage temperature range ? 55 to +150 c esd susceptibility (human body model) 2.0 kv lead temperature soldering wave solder (through hole styles only) note 1 reflow (smd styles only) note 2 260 peak 230 peak c c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. 10 seconds max. 2. 60 seconds max above 183 c *the maximum package power dissipation must be observed.
CS8363 http://onsemi.com 3 electrical characteristics (6.0 v v in 26 v, i out1 = i out2 = 100 a, ? 40 c t a +125 c; unless otherwise stated.) characteristic test conditions min typ max unit tracking output (v trk ) v trk tracking error (v stby ? v trk ) 6.0 v v in 26 v, 100 a i trk 250 ma. note 3 ? 25 ? +25 mv adjust pin current, i adj loop in regulation ? 1.5 5.0 a line regulation 6.0 v v in 26 v. note 3 ? 5.0 50 mv load regulation 100 a i trk 250 ma. note 3 ? 5.0 50 mv dropout voltage (v in ? v trk ) i trk = 100 a. i trk = 250 ma ? ? ? ? 1.05 1.05 mv mv current limit v in = 12 v, v trk = 3.0 v 275 500 ? ma quiescent current v in = 12 v, i trk = 250 ma, no load on v stby v in = 12 v, i trk = 500 a, i stby = 100 a ? ? 25 145 50 220 ma a reverse current v trk = 3.3 v, v in = 0 v ? 200 1500 a ripple rejection f = 120 hz, i trk = 250 ma, 7.0 v v in 17 v 60 70 ? db standby output (v stby ) output voltage, v stby 4.5 v v in 26 v, 100 a i stby 100 ma. 3.234 3.3 3.380 v line regulation 6.0 v v in 26 v. ? 5.0 50 mv load regulation 100 a i stby 100 ma. ? 5.0 50 mv dropout voltage (v in ? v stby ) i stby = 100 a, v in = 4.2 v i stby = 100 ma, v in = 4.2 v ? ? ? ? 1.05 1.05 v v current limit v in = 12 v, v stby = 3.0 v 125 200 ? ma short circuit current v in = 12 v, v stby = 0 v 10 100 ? ma quiescent current v in = 12 v, i stby = 100 ma, i trk = 0 ma v in = 12 v, i stby = 300 a, i trk = 0 ma ? ? 10 140 20 200 ma a reverse current v stby = 3.3 v, v in = 0 v ? 100 200 a ripple rejection f = 120 hz, i stby = 100 ma, 7.0 v v in 17 v 60 70 ? db reset enable functions enable input threshold ? 0.8 1.2 2.0 v enable input bias current v enable = 0 v to 10 v ? 10 0 10 a reset hysteresis ? 10 50 150 mv reset threshold low (v rl ) v stby decreasing, v in > 4.5 v 92.5 95 97.5 %v stby reset leakage ? ? ? 25 a output voltage, low (v rlo ) 1.0 v v stby v rl , r rst = 10 k ? 0.1 0.4 v output voltage, low (v rpeak ) v stby , power up, power down ? 0.6 1.0 v v in (v rst low) v stby = 3.3 v ? 4.0 4.5 v protection circuitry (both outputs) independent thermal shutdown v stby v trk 150 150 180 165 ? ? c c overvoltage shutdown ? 30 34 38 v 3. v trk connected to adj lead. v trk can be set to higher values by using an external resistor divider.
CS8363 http://onsemi.com 4 package pin description package pin # pin symbol function d 2 pak ? 7 1 v stby standby output voltage delivering 100 ma. 2 v in input voltage. 3 v trk tracking output voltage controlled by enable delivering 250 ma. 4 gnd reference ground connection. 5 adj resistor divider from v trk to adj. sets the output voltage on v trk . if tied to v trk , v trk will track v stby . 6 enable provides on/off control of the tracking output, active low. 7 reset cmos compatible output lead that goes low whenever v stby falls out of regulation. circuit description enable function the enable function switches the output transistor for v trk on and off. when the enable lead voltage exceeds 1.4 v (typ), v trk turns off. this input has several hundred millivolts of hysteresis to prevent spurious output activity during power ? up or power ? down. reset function the reset is an open collector npn transistor, controlled by a low voltage detection circuit sensing the v stby (3.3 v) output voltage. this circuit guarantees the reset output stays below 1.0 v (0.1 v typ) when v stby is as low as 1.0 v to ensure reliable operation of microprocessor ? based systems. v trk output voltage this output uses the same type of output device as v stby , but is rated for 250 ma. the output is configured as a tracking regulator of the standby output. by using the standby output as a voltage reference, giving the user an external programming lead (adj lead), output voltages from 3.3 v to 20 v are easily realized. the programming is done with a simple resistor divider, and following the formula: v trk v stby (1 r1 r2) i adj r1 if another 3.3 v output is needed, simply connect the adj lead to the v trk output lead. c1* 0.1 f gnd CS8363 mcu b+ v in v trk adj enable reset v stby r3 v dd c2** 10 f esr < 8.0 3.3 v, 100 ma reset i/o r2 r1 c3** 10 f esr < 8.0 sw 5.0 v, 250 ma gnd v trk v stby (1 + r1/r2) for v trk 5.0 v, r1/r2 0.5 *c1 is required if regulator is located far from power supply filter. **c2 and c3 are required for stability. figure 2. test and application circuit, 3.3 v, 5.0 v regulator
CS8363 http://onsemi.com 5 c1* 0.1 f gnd CS8363 mcu b+ v in v trk adj enable reset v stby r3 v dd c2** 10 f esr < 8.0 3.3 v, 100 ma reset i/o c3** 10 f esr < 8.0 sw 3.3 v, 250 ma gnd *c1 is required if regulator is located far from power supply filter. **c2 and c3 are required for stability. figure 3. test and application circuit, dual 3.3 v regulator application notes external capacitors output capacitors for the CS8363 are required for stability. without them, the regulator outputs will oscillate. actual size and type may vary depending upon the application load and temperature range. capacitor ef fective series resistance (esr) is also a factor in the ic stability. worst ? case is determined at the minimum ambient temperature and maximum load expected. output capacitors can be increased in size to any desired value above the minimum. one possible purpose of this would be to maintain the output voltages during brief conditions of negative input transients that might be characteristic of a particular system. capacitors must also be rated at all ambient temperatures expected in the system. to maintain regulator stability down to ? 40 c, capacitors rated at that temperature must be used. more information on capacitor selection for smart regulator ? s is available in the smart regulator application note, ?compensation for linear regulators,? document number sr003an/d, available through the literature distribution center or via our website at http://www.onsemi.com. calculating power dissipation in a dual output linear regulator the maximum power dissipation for a dual output regulator (figure 4) is p d(max) v in(max) v out1(min) i out1(max) v in(max) v out2(min) i out2(max) v in(max) iq (1) where: v in(max) is the maximum input voltage, v out1(min) is the minimum output voltage from v out1 , v out2(min) is the minimum output voltage from v out2 , i out1(max) is the maximum output current, for the application, i out2(max) is the maximum output current, for the application, and i q is the quiescent current the regulator consumes at both i out1(max) and i out2(max) . once the value of p d(max) is known, the maximum permissible value of r ja can be calculated: r ja 150 c t a p d (2) the value of r ja can be compared with those in the package section of the data sheet. those packages with r ja ?s less than the calculated value in equation 2 will keep the die temperature below 150 c. in some cases, none of the packages will be sufficient to dissipate the heat generated by the ic, and an external heatsink will be required. figure 4. dual output regulator with key performance parameters labeled. smart regulator control features v out1 i out1 v out2 i out2 v in i in i q
CS8363 http://onsemi.com 6 heat sinks a heat sink effectively increases the surface area of the package to improve the flow of heat away from the ic and into the surrounding air. each material in the heat flow path between the ic and the outside environment will have a thermal resistance. like series electrical resistances, these resistances are summed to determine the value of r ja : r ja r jc r cs r sa (3) where: r jc = the junction ? to ? case thermal resistance, r cs = the case ? to ? heatsink thermal resistance, and r sa = the heatsink ? to ? ambient thermal resistance. r jc appears in the package section of the data sheet. like r ja , it too is a function of package type. r cs and r sa are functions of the package type, heatsink and the interface between them. these values appear in heat sink data sheets of heat sink manufacturers.
CS8363 http://onsemi.com 7 package dimensions d 2 pak ? 7 (short lead) dps suffix case 936ab ? 01 issue b 0.539 dim min max min max millimeters inches e 0.380 0.420 9.65 10.67 d 0.325 0.368 8.25 9.53 a 0.170 0.180 4.32 4.57 b 0.026 0.036 0.66 0.91 c2 0.045 0.055 1.14 1.40 e 0.050 bsc 1.27 bsc h 0.579 13.69 14.71 l1 a1 0.000 0.010 0.00 0.25 c 0.017 0.026 0.43 0.66 e d l1 c2 c b e e1 d1 h ??? 0.066 ??? 1.68 l 0.058 0.078 1.47 1.98 m l3 0.010 bsc 0.25 bsc 0 8 0 8 *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. recommended notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: inches. 3. dimensions d and e do not include mold flash and gate protrusions. mold flash and gate protrusions not to exceed 0.005 maximum per side. these dimensions to be measured at datum h. 4. thermal pad contour optional within dimensions e, l1, d1, and e1. dimensions d1 and e1 establish a minimum mounting surface for the thermal pad. d1 0.270 ??? 6.86 ??? e1 0.245 ??? 6.22 ??? a dimensions: millimeters 0.424 7x 0.584 0.310 0.136 0.040 0.050 pitch soldering footprint* a1 l3 b h l m detail c seating plane gauge plane a 7x m a m 0.13 b e/2 b seating plane a a detail c view a ? a m a m 0.10 b package thermal data parameter d 2 pak ? 7 unit r jc typical 3.5 c/w r ja typical 10 ? 50* c/w *depending on thermal properties of substrate. r ja = r jc + r ca .
CS8363 http://onsemi.com 8 on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. CS8363/d smart regulator is a registered trademark of semiconductor components industries, llc (scillc). publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5773 ? 3850 literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
