|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
service manual data nsx?l54 rc?as01 system cd casseiver remote controller cx?bl54 compact disc stereo system basic tape mechanism : 2zm-3mk2 pr4nm(hs/hr) basic tape mechanism : 6zm-3 pr2nm(k/ez) basic cd mechanism : azg-1 ykza3rdf(hs/hr) basic cd mechanism : azg-1 ykzd8rdf(k/ez) NSX-BL54 nsx-bl56 ez,k,hs,hr ez s/m code no. 09-002-429-5r1 revision this service manual is the "revision publishing" and replaces "simple manual" NSX-BL54 2 main unit cx-nbl54, cx-nbl56 fm tuner section tuning range 87.5 mhz to 108 mhz usable sensitivity (ihf) 16.8 dbf tuning range 5.730 mhz to 17.900 mhz antenna wire antenna amplifier section mid-high frequency amplifier power output rated: 20 w + 20 w (8 ohms, t.h.d. 1 %, 1 khz/din 45500) reference : 25 w + 25 w (8 ohms, t.h.d. 10 %, 1 khz/din 45324) din music power: 40 w + 40 w power consumption 150 w power consumption in standby mode if the power-economizing mode is eco off: 20 w if the power-economizing mode is eco on or eco auto: 0.9 w dimensions of main unit 260 x 326 x 345 mm (w x h x d) weight of main unit 9.0 kg speaker system sx-wnbl53, sx-wnbl56 speaker system 3 way, built-in subwoofer (magnetic shielded type) speaker units subwoofer: 160 mm cone type full range: 100 mm cone type super tweeter: 20 mm ceramic type impedance 6 ohms/8 ohms sensitvity 87 db/w/m dimensions (w x h x d) 230 x 324 x 282 mm weight 4.8 kg ref. no part no. kanri description no. accessories list 1 8a-nfj-905-010 ib,k(e)m 2 8z-nf8-702-010 rc unit,rc-zas01 3 87-006-268-010 ant,loop am 4 87-a90-118-010 ant,wire fm(z) design and specifications are subject to change without notice. the word ?be?and the ?be symbol?are trademarks of bbe sound, inc. under license from bbe sound, inc. ref. no part no. kanri description no. ! 6 87-a91-017-010 plug,conversion jt-0476 ! 6 87-099-811-010 plug,adptr conv(k) 3 protection of eyes from laser beam during servicing varoitus! laiteen k?ytt?minen muulla kuin t?ss? k?ytt?ohjeessa mainit- ulla tavalla saattaa altistaa k?yt-t?j?n turvallisuusluokan 1 ylit- t?v?lle n?kym?tt?m?lle lasers?teilylle. varning! om apparaten anv?nds p? annat s?tt ?n vad som specificeras i denna bruksanvising, kan anv?ndaren uts?ttas f?r osynling laserstr?lning, som ?verskrider gr?nsen f?r laserklass 1. caution: invisible laser radiation when open and interlocks defeated avoid expo- sure to beam. advarsel:usynling laserst?ling ved ?bning, n?r sikkerhedsafbrydere er ude af funktion. undg? uds?ttelse for str?ling. caution use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. attention l'utilisation de commandes, rglages ou procdures autres que ceux spcifis peut entra?ner une dangereuse exposition aux radiations. advarsel! usynlig laserst?ling ved ?bning, n?r sikkerhedsafbrydereer ude af funktion. undg? uds?ttelse for str?ling. this compact disc player is classified as a class 1 laser product. the class 1 laser product label is located on the rear exterior. this set employs laser. therefore, be sure to follow carefully the instructions below when servicing. warning! when servicing, do not approach the laser exit with the eye too closely. in case it is necessary to confirm laser beam emission. be sure to observe from a distance of more than 30cm from the surface of the objective lens on the optical pick-up block. class 1 klasse 1 luokan 1 klass 1 laser product laser produkt laser laite laser apparat precaution to replace optical block 1) after the connection, remove solder shown in the figure below. body or clothes electrostatic potential could ruin laser diode in the optical block. be sure ground body and workbench, and use care the clothes do not touch the diode. solder z a 8 / zd 8 model za3/za4 model ( k ss - 21 3 f ) 4 note on before starting repair charging voltage (v) discharging rated power (w) parts number (c101, 102) resistor ( ? ) 25-48 100 3 87-a00-247-090 49-140 220 5 87-a00-232-090 note: the reference numbers (c101, c102) of the electrolytic capacitors can change depending on the models. be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. check items before exchanging the microcomputer be sure to check the following items before exchanging the microcomputer. exchange the microcomputer after confirming that the microcomputer is surely defective. 2-1. regarding the hold terminal of the microcomputer when the hold terminal (input) of the microcomputer is ?? the microcomputer is judged to be operating correctly. when this terminal is ?? the main power cannot be turned on. therefore, be sure to check the terminal voltage of the hold terminal before exchange. when the microcomputer is not defective, the hold terminal can also go ??when the power amplifier has any abnormalities that triggers the abnormality detection circuit on the main c. b. that sets the hold terminal to ?? good or no good judgement of the microcomputer 1 turn on the ac main power. 2 confirm that the main power is turned on and the hold terminal of the microcomputer keeps the ??level or not. 3 when the hold terminal is ??level, the abnormality detection circuit is judged to be working correctly and the microcomputer is judged to be good. 1. forced discharge of electrolytic capacitor of power supply block when repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept c harged across the electrolytic capacitors (c101, 102) even though ac power cord is removed. if repair is attempted in this condition, second ary defect can occur. in order to prevent the secondary trouble, perform the following measures before starting repair work. discharge procedure 1 remove the ac power cord. 2 connect a discharging resistor at an end of lead wire that has clips at both ends. connect the other end of the lead wire to metal chassis. 3 contact the other end of the discharging resistor to the positive (+) side (+vh) of c101. (for two seconds) 4 contact the same end of the discharging resistor as step 3 to the negative (-) side (-vh) of c102 in the same way. (for two seconds) 5 check that voltage across c101 and c102 has decreased to 1 v or less using a multimeter or an oscilloscope. select a discharging resistor referring to the following table. main c.b d101 c101 c102 3 4 22 5 in such a case, check also if the power amplifier circuit or power supply circuit has any abnormalities or not. 2-2. regarding reset there are cases that the machine does not work correctly because the microcomputer is not reset even though the ac power cord is re-inserted, or the software reset (pressing the stop key + power key) is performed. when the above described phenomenon occurs, it can lead to wrong judgement as if the microcomputer is defective and to exchange the microcomputer. in such a case, perform the forced-reset by the following procedure and check good or no good of the microcomputer. 1 remove the ac power cord. 2 short both ends of the electrolytic capacitor c113 that is connected to vdd of the microcomputer with tweezers. 3 connect the ac power cord again. if the microcomputer returns to the normal operation, the microcomputer is good. note: the reference number or microcomputer pin number of transistor (q110) and electrolytic capacitor (c113) can change depending on the models. be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. confirmation of soldering state of microcomputer check the soldering state of the microcomputer in addition to the above described procedures. be sure to exchange the microcomputer after surely confirming that the trouble is not caused by poor soldering but the microcomputer itself. fig-2-2 micro- computer microcomputer front c.b front c.b vss vdd c113 18 15 c113 18 15 short with tweezers. 6 ref. no part no. kanri description no. ref. no part no. kanri description no. electrical main parts list ic 87-020-454-010 ic,dn6851 87-a21-417-010 ic,stk490-310 8a-nf8-614-110 c-ic,lc866560w-5p89< 5 6ez> 8a-nf8-613-010 c-ic,lc866548v-5p87 87-a21-023-040 c-ic,ba3835f 87-a30-086-070 c-tr,csd1306e c0110 87-010-179-080 c-cap,s 1200p-50 k b grm c0111 87-010-405-080 cap,e 10-50 m 11l sme c0112 87-010-405-080 cap,e 10-50 m 11l sme c0113 87-010-866-080 cap,e 10-63 m vx c0114 87-010-866-080 cap,e 10-63 m vx c0119 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0120 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0123 87-010-176-080 c-cap,s 680p-50 j sl c0205 87-012-140-080 c-cap,s 470p-50 j ch c0206 87-012-140-080 c-cap,s 470p-50 j ch 7 ref. no part no. kanri description no. ref. no part no. kanri description no. c0229 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0230 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0231 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0232 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0233 87-010-190-080 c-cap,s 0.01-50 z f c0789 87-a11-532-080 c-cap,s 0.022-50 j b c0790 87-a11-532-080 c-cap,s 0.022-50 j b 8 c0852 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0853 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0858 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0859 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0860 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0869 87-010-197-080 c-cap,s 0.01-25 k b c2012< 5 6ez> c0870 87-018-131-080 cap,tc u 1000p-50 k b up050< 5 6ez> c0871 87-012-156-080 c-cap,s 220p-50 j ch grm< 5 6ez> c0872 87-012-156-080 c-cap,s 220p-50 j ch grm< 5 6ez> c0873 87-012-140-080 c-cap,s 470p-50 j ch< 5 6ez> c0874 87-010-405-080 cap,e 10-50 m 11l sme< 5 6ez> c0875 87-010-196-080 c-cap,s 0.1-25 z f c2012< 5 6ez> c0876 87-010-405-080 cap,e 10-50 m 11l sme< 5 6ez> c0877 87-010-197-080 c-cap,s 0.01-25 k b c2012< 5 6ez> c0878 87-010-316-080 c-cap,s 33p-50 j ch grm< 5 6ez> c0879 87-010-314-080 c-cap,s 22p-50 j ch grm< 5 6ez> c0940 87-010-197-080 c-cap,s 0.01-25 k b c0942 87-010-149-080 c-cap,s 5p-50 c ch c0945 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0946 87-010-971-080 c-cap,s 4700p-50 j b c0947 87-010-197-080 c-cap,s 0.01-25 k b c0948 87-012-140-080 c-cap,s 470p-50 j ch c0954 87-010-400-080 cap,e 0.47-50 m 11l sme c0956 87-010-263-080 cap,e 100-10 m 11l sme c0957 87-010-311-080 c-cap,s 12p-50 j ch c0971 87-010-381-080 cap,e 330-16 m sme c0972 87-010-404-080 cap,e 4.7-50 m 11l sme c0973 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0974 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0979 87-010-322-080 c-cap,s 100p-50 j ch grm c0981 87-010-260-080 cap,e 47-25 m 11l sme c0982 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0983 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0984 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0985 87-010-322-080 c-cap,s 100p-50 j ch ffc0602 88-906-251-110 ff-cable,6p 1.25 ffe0831 a8-6za-195-130 6za-1 yfeenm l0101 87-003-383-010 coil,1uh k l0102 87-003-383-010 coil,1uh k l0201 87-003-383-010 coil,1uh k l0202 87-003-383-010 coil,1uh k l0451 87-007-342-010 coil,osc 85khz bias l0801 87-a50-608-010 coil,fm det-n(tok) l0802 87-a91-551-010 fltr,pcfjzh-450 l l0811 87-005-847-080 coil,2.2uh k cecs l0832 87-005-847-080 coil,2.2uh k cecs l0861 87-005-847-080 coil,2.2uh k cecs< 5 6ez> l0941 87-a50-020-010 coil,ant lw 252khz l0942 87-a50-019-010 coil,osc lw 856khz l0943 87-a50-522-080 coil,1mh k cec l0944 87-a50-159-010 coil,10mh k c2b l0951 8a-nf8-667-010 coil,am pack 4(tok) l0953 87-a50-431-010 coil,osc mw(3bsw) r0129 87-a00-257-080 res,m/f 0.15-1w j r0130 87-a00-257-080 res,m/f 0.15-1w j r0143 87-a00-439-050 res,180-1/2w j rp tc0942 87-011-253-080 trimmer,cer 30p 4.0x4.5 wh0001 87-a91-179-010 hldr,wire 2.5-11p x0861 87-a70-091-010 vib,xtal 4.332mhz csa-309< 5 6ez> x0991 87-a70-061-010 vib,xtal 4.500mhz csa-309 front c.b c0201 87-010-322-080 c-cap,s 100p-50 j ch grm c0202 87-010-322-080 c-cap,s 100p-50 j ch grm c0203 87-010-322-080 c-cap,s 100p-50 j ch grm c0204 87-010-322-080 c-cap,s 100p-50 j ch grm c0205 87-010-322-080 c-cap,s 100p-50 j ch grm c0206 87-010-322-080 c-cap,s 100p-50 j ch grm c0207 87-010-322-080 c-cap,s 100p-50 j ch grm c0208 87-010-322-080 c-cap,s 100p-50 j ch grm c0209 87-010-322-080 c-cap,s 100p-50 j ch grm c0210 87-010-322-080 c-cap,s 100p-50 j ch grm c0211 87-010-322-080 c-cap,s 100p-50 j ch grm c0251 87-010-405-040 cap,e 10-50 m 11l sme ref. no part no. kanri description no. ref. no part no. kanri description no. 9 c0253 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0254 87-012-369-080 c-cap,s 0.047-50 z f c0255 87-010-560-040 cap,e 10-50 m 5l ma c0256 87-010-405-040 cap,e 10-50 m 11l sme c0259 87-010-405-040 cap,e 10-50 m 11l sme c0264 87-a11-148-080 cap,tc u 0.1-50 z f c0273 87-010-178-080 c-cap,s 1000p-50 k b c2012 c0274 87-010-178-080 c-cap,s 1000p-50 k b c2012 c0301 87-010-182-080 c-cap,s 2200p-50 k b c2012 c0302 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0303 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0312 87-010-498-040 cap,e 10-16 m 5l sre c0314 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0315 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0316 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0321 87-012-393-080 c-cap,s 0.22-16 k w5r cm/cb c0322 87-010-400-040 cap,e 0.47-50 m 11l sme c0325 87-a10-189-040 cap,e 220-10 m 5l c0326 87-a10-189-040 cap,e 220-10 m 5l c0332 87-010-178-080 c-cap,s 1000p-50 k b c2012 c0334 87-010-312-080 c-cap,s 15p-50 j ch grm c0335 87-012-140-080 c-cap,s 470p-50 j ch c0336 87-012-155-080 c-cap,s 180p-50 j ch grm c0339 87-012-156-080 c-cap,s 220p-50 j ch grm c0340 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0341 87-010-194-080 c-cap,s 0.047-25 z f c0351 87-010-981-040 cap,e 22-35 m 5l sre c0401 87-010-197-080 c-cap,s 0.01-25 k b c2012 c0451 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0452 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0453 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0454 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0455 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0458 87-010-320-080 c-cap,s 68p-50 j ch grm c0459 87-010-320-080 c-cap,s 68p-50 j ch grm c0502 87-010-186-080 c-cap,s 4700p-50 k b c0602 87-010-322-080 c-cap,s 100p-50 j ch grm c0603 87-010-322-080 c-cap,s 100p-50 j ch grm c0604 87-010-322-080 c-cap,s 100p-50 j ch grm c0650 87-010-196-080 c-cap,s 0.1-25 z f c2012 c0699 87-010-196-080 c-cap,s 0.1-25 z f c2012 cn0101 87-099-720-010 conn,30p blk tyk-b(p) cn0102 87-099-015-010 conn,13p v blk 6216 cn0301 87-a60-140-010 conn,15p v fe s0402 87-a90-095-080 sw,tact evq11g04m s0403 87-a90-095-080 sw,tact evq11g04m s0404 87-a90-095-080 sw,tact evq11g04m s0405 87-a90-095-080 sw,tact evq11g04m s0406 87-a90-095-080 sw,tact evq11g04m s0407 87-a90-095-080 sw,tact evq11g04m s0408 87-a90-095-080 sw,tact evq11g04m s0409 87-a90-095-080 sw,tact evq11g04m s0410 87-a90-095-080 sw,tact evq11g04m s0411 87-a90-095-080 sw,tact evq11g04m s0412 87-a90-095-080 sw,tact evq11g04m< 5 6ez,hs> s0412 87-a91-024-180 sw,tact kshg611bt s0413 87-a90-095-080 sw,tact evq11g04m s0414 87-a90-095-080 sw,tact evq11g04m s0415 87-a90-095-080 sw,tact evq11g04m s0416 87-a90-095-080 sw,tact evq11g04m s0417 87-a90-095-080 sw,tact evq11g04m s0418 87-a90-095-080 sw,tact evq11g04m s0419 87-a90-095-080 sw,tact evq11g04m s0420 87-a90-095-080 sw,tact evq11g04m< 5 6ez,hs> s0420 87-a91-024-180 sw,tact kshg611bt s0421 87-a90-095-080 sw,tact evq11g04m< 5 6ez> s0425 87-a90-095-080 sw,tact evq11g04m s0426 87-a90-095-080 sw,tact evq11g04m s0432 87-a90-095-080 sw,tact evq11g04m s0433 87-a90-095-080 sw,tact evq11g04m s0434 87-a90-095-080 sw,tact evq11g04m s0435 87-a90-095-080 sw,tact evq11g04m s0436 87-a90-095-080 sw,tact evq11g04m s0437 87-a90-095-080 sw,tact evq11g04m sw0252 87-a91-555-010 sw,rtry ec12e24504 sw0253 87-a91-542-010 sw,rtry ec12e12504 vr0501 86-nfa-607-010 vr,rtry 10k15ax1 1 v 10 sol2 82-zm1-618-410 sol assy,27 sw1 87-a90-248-010 sw,micro ese11sh2cxq sw2 87-a90-248-010 sw,micro ese11sh2cxq sw3 87-a90-248-010 sw,micro ese11sh2cxq sw4 87-036-110-010 sw,micro sppb62 sw5 87-036-110-010 sw,micro sppb62 sw6 87-036-110-010 sw,micro sppb62 12 11 fl (hna-11mm30) grid assignment/anode connection grid assignment anode connection 14 13 schematic diagram-1 (function/amp section) 16 15 schematic diagram-2 (tuner section) 18 17 schematic diagram-3 (tuner section) 20 19 schematic diagram-4 (tuner section) 1 234567 8 9 10 11 12 13 14 a b c d e f g h i j 22 21 wiring-1 (main c.b) 1 234567 8 9 10 11 12 13 14 a b c d e f g h i j 24 23 wiring-2 (main c.b) tp7 25 schematic diagram-5 (front section) 1 234567 8 9 10 11 12 13 14 a b c d e f g h i j 28 27 wiring-3 (front c.b) 1 234567 8 9 10 11 12 13 14 a b c d e f g h i j 30 29 wiring-4 (front c.b) tp7 32 31 schematic diagram-6 (front section) 34 33 schematic diagram-7 (pt section) 1 23456 7 a b c d e f 1 23456 7 a b c d e f g h i j 36 35 schematic diagram-8 (pt section) tf tf 1 23456 7 a b c d e f g h i j 38 37 wiring-9 (deck c.b) 39 ic, ba3835f ic, bu2092f ic, m61503fp ic, m61506fp pin no. pin name i/o description 40 ic description i i o o o o o o o o o i i i i i i i i i i i i i o o o o o o o i/o i/o i/o stereo detected input/cd drf input tune if count serial data input/cd subq input deck 2 playback switch output _______ system power supply on/off output _______ cd power on/off output led driver, tuner ic, function ic data output deck 2 rec mute output _____ deck 2 bias on/off output _______ system mute on/off output latch strobe output for led driver ic micon clock shift output system reset not connected cd turntable photo sensor a/d converter input gnd 5.76 mhz oscillator circuit 5.76 mhz oscillator circuit power supply input power failure detected input key input (a/d) key input (a/d) key input (a/d) tuner signal input cd mechanical switch a/d converter input a/d input for spectrum analyzer display rotary encoder input (vol) cd wrq input/tuner rds clock input reference clock input for timer watch system remotecontrol signal input fl grid output g11 ~ g1 not connected fl segment output p35 ~ p32 power supply input fl segment output p31 ~ p30 fl segment output p29/spectrum analyzer band switching output fl segment output p28/spectrum analyzer band switching output power supply input for fl display fl segment output p27/spectrum analyzer band switch output fl segment output p26 fl segment output p25/no casino demo input to diode fl segment output p24/karaoke input to diode fl segment output p23/no demo input to diode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 ~ 40 41 42 ~ 45 46 47 ~ 48 49 50 51 52 53 54 55 56 _______________ i-stereo/i-drf ______ i-ifc/i-subq o-2pb o-power o-cd-on o-pll_data o-rmt _________ o-bias o-mute o-stb _________________ o-clk_sft reset nc i-dish vss1 cf1 cf2 vdd1 __________ i-hold i-key1 i-key2 i-key3 i-tu_sig i-cdsw i-speana i-re_vol i-wrq/i-rds_clk i-tm_base _________ i-rmc g11 ~ g1 nc p35 ~ p32 vdd3 p31 ~ p30 p29/o-speana-c p28/o-speana-b vfl p27/o-speana-a p26 p25/i-no_casino p24/i-karaoke p23/no_demo ic, lc866560w-5p89 <56ez>, lc866548v-5p87 pin no. pin name i/o description 41 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 ~ 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 p22/pro logic p21/rds p20/fm1 p19/sw p18/lw p17/amst p16/am10k _________ p15/i-cst2 ________ p14/i-reb ___________ p13/i-cam2 ____________ p12/i-auto1 _____________ p11/i-auto2 __________ p10/i-cam1 _________ p9/i-cst1 ________ p8/i-rea vdd4 p7/i-rev2 p6/i-rev1 p5/no_eco p4 ~ p1 o-cd close o-cd open nc i-jog_a i-jog_b o-dish_fwd o-dish_rev o-pll_ce _____________ o-kscan vss2 vdd2 _________ led-stby ______________ o-motor _________ o-sol1 _________ o-sol2 o-cd-data o-cd-led o-cd clk o-cd ce i-rds_data o-pll_clk i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o i/o o o o i i o o o o o o o o o o o o i o fl segment output p22/prologic input to diode (not used) fl segment output p21/rds input to diode fl segment output p20/fm1 input to diode fl segment output p19/sw input to diode fl segment output p18/lw input to diode fl segment output p17/amst input to diode fl segment output p16/am10k input to diode fl segment output p15/deck2 cassette detect switch data input fl segment output p14/deck2 side-b record ok switch data input fl segment output p13/deck2 cam switch signal input fl segment output p12/deck1 auto stop signal input fl segment output p11/deck2 auto stop signal input fl segment output p10/deck1 cam switch data input fl segment output p9/deck1 cassette detect switch data input fl segment output p8/deck2 side a record ok switch data input power supply input fl segment output p7/deck2 reverse mode input to diode fl segment output p6/deck1 reverse mode input to diode fl segment output p5/no eco mode input to diode fl segment output p4 ~ p1 cd tray close data output cd tray open data output not connected rotary encoder a input (jog) rotary encoder b input (jog) cd turntable forward rotation output cd turntble reverse rotation output pll ic chip enable output switch scan timing output gnd power supply input stand by led (echo mode) ouput _____ deck motor on/off output deck1 soleroid ouput deck2 soleroid ouput cd data output cd led output cd clock output cd chip enable output rds data input pll ic clock output 42 adjustment 43 < tuner section > 1. clock frequency check settings : ?test point : tp2 method : set to am 1602khz and check that the test point is 2052khz 45hz. 2. mw vt check settings : ?test point : tp1 (vt) method : set to mw 1602khz, 531khz and check that the test point is less than 8.0v (1602khz) and more than 0.6v (531khz). 3. lw vt adjustment settings : ?test point : tp1 (vt) ?adjustment location: l942 method : set to lw 144khz and adjust l942 so that the test point is 1.3v 0.05v. then set to lw 290khz and check that the test point is less than 8.0v. 4. fm vt check settings : ?test point : tp1 (vt) method : set to fm 87.5mhz, 108.0mhz and check that the test point is more than 0.5v (87.5mhz) and less than 8.0v (108.0mhz). 5. mw tracking adjustment settings : test point : tp8(lch), tp9(rch) ?adjustment location : l951(1/3) ...................................... 999khz method : set to mw 999khz and adjust l951(1/3) so that the level at the test point becomes maximum. 6. lw tracking adjustment settings : ?test point : tp8(lch), tp9(rch) ?adjustment location : l941, tc942 method : set up tc942 to center position. set to lw 144khz and adjust l941 so that the level at test point becomes maximum. then set to lw 290khz and adjust tc942 so that the level at test point becomes maximum. 7. fm tracking check settings : ?test point : tp8(lch), tp9(rch) method : set to fm 98.0mhz and check that the test point is less than 13db v. 8. am if adjustment settings : ?test point : tp8(lch), tp9(rch) ?adjustment location : l802 ............................................. 999khz 9. dc balance / mono distortion adjustment settings : ?test point : tp3, tp4 (dc balance) : tp8(lch), tp9(rch) (distortion) ?adjustment location : l801 ?input level : 60db v method : set to fm 98.0mhz and adjust l801 so that the voltage between tp3 and tp4 becomes 0v 0.3v. next, check that the distortion is less than 1.3%. < deck section > 10. tape speed adjustment (deck 2) settings : test tape : tta?00 ?test point : tp8(lch), tp9(rch) ?adjustment location : sfr1 method : play back the test tape and adjust sfr1 so that the frequency counter reads 3000hz 5hz and 45hz (rev) with respect to forward speed. 11. head azimuth adjustment (deck 1, deck 2) settings : test tape : tta?30 ?test point : tp8(lch), tp9(rch) ?adjustment location : head azimuth adjustment screw method : play back (fwd) the 8khz signal of the test tape and adjust screw so that the output becomes maximum. next, perform on rev play mode. 12. pb frequency response check (deck 1, deck 2) settings : test tape : tta?00 ?test point :tp8(lch), tp9(rch) method : play back the 315hz and 8khz signals of the test tape and check that the output ratio of the 8khz signal with respect to that of the 315hz signal is within 5db. 13. pb sensitivity check (deck 1, deck 2) settings : test tape : tta?00 ?test point : tp8(lch), tp9(rch) method : play back the test tape and check that the output level of the test point is 140mv 3db. 14. rec/pb frequency response adjustment (deck 2) settings : test tape : tta?02 ?test point : tp8(lch), tp9(rch) ?input signal : 1khz / 8khz (line in) ?adjustment location : sfr451 (lch) sfr452 (rch) method : apply a 1khz signal and rec mode. then adjust osc attenuator so that the output level at the tp8, tp9 becomes -20vu. record and play back the 1khz and 8khz signals and adjust sfrs so that the output of the 8khz signals becomes 0db 0.5db with respect to that of the 1khz signal. 15. rec/pb sensitivity check (deck 2) settings : test tape : tta?02 ?test point : tp8(lch), tp9(rch) ?input signal : 1khz (line in) method : apply a 1khz signal and rec mode. then adjust osc attenuator so that the output level at tp8, tp9 becomes 0vu. record and play back the 1khz signals and check that the output is ?db 3.0db. < front section > 16. -con osc adjustment settings : test point : tp7 and gnd ?adjustment location : l331 method : insert ac plug while pressing power and tuner function keys. adjust l331 so that the frequency atthe test point is 153.84hz 0.15hz. 44 adjustment 45 < tuner section > 1. clock frequency check settings : ?test point : tp2 method : set to am 1602khz and check that the test point is 2052khz 45hz. 2. am vt check settings : ?test point : tp1 (vt) method : set to am 1710khz, 530khz and check that the test point is less than 8.5v (1710khz) and more than 0.6v (530khz). 3. fm vt check settings : ?test point : tp1 (vt) method : set to fm 87.5mhz, 108.0mhz and check that the test point is more than 0.5v (87.5mhz) and less than 8.0v (108.0mhz). 4. am tracking adjustment settings : test point : tp8(lch), tp9(rch) ?adjustment location : l951(1/3) ...................................... 1000khz method : set to am 1000khz and adjust l951(1/3) so that the level at the test point becomes maximum. 5. fm tracking check settings : ?test point : tp8(lch), tp9(rch) method : set to fm 98.0mhz and check that the test point is less than 9db v. 6. am if adjustment settings : ?test point : tp8(lch), tp9(rch) ?adjustment location : l802 ............................................. 1000khz 7. dc balance / mono distortion adjustment settings : ?test point : tp3, tp4 (dc balance) : tp8(lch), tp9(rch) (distortion) ?adjustment location : l801 ?input level : 60db v method : set to fm 98.0mhz and adjust l801 so that the voltage between tp3 and tp4 becomes 0v 0.3v. next, check that the distortion is less than 1.3%. < deck section > 8. tape speed adjustment (deck 2) settings : test tape : tta?00 ?test point : tp8(lch), tp9(rch) ?adjustment location : sfr1 method : play back the test tape and adjust sfr1 so that the frequency counter reads 3000hz 5hz and 45hz (rev) with respect to forward speed. 9. head azimuth adjustment (deck 1, deck 2) settings : test tape : tta?30 ?test point : tp8(lch), tp9(rch) ?adjustment location : head azimuth adjustment screw method : play back (fwd) the 8khz signal of the test tape and adjust screw so that the output becomes maximum. next, perform on rev play mode. 10. pb frequency response check (deck 1, deck 2) settings : test tape : tta?00 ?test point :tp8(lch), tp9(rch) method : play back the 315hz and 8khz signals of the test tape and check that the output ratio of the 8khz signal with respect to that of the 315hz signal is within 5db. 11. pb sensitivity check (deck 1, deck 2) settings : test tape : tta?00 ?test point : tp8(lch), tp9(rch) method : play back the test tape and check that the output level of the test point is 140mv 3db. 12. rec/pb frequency response adjustment (deck 2) settings : test tape : tta?02 ?test point : tp8(lch), tp9(rch) ?input signal : 1khz / 8khz (line in) ?adjustment location : sfr451 (lch) sfr452 (rch) method : apply a 1khz signal and rec mode. then adjust osc attenuator so that the output level at the tp8, tp9 becomes -20vu. record and play back the 1khz and 8khz signals and adjust sfrs so that the output of the 8khz signals becomes 0db 0.5db with respect to that of the 1khz signal. 13. rec/pb sensitivity check (deck 2) settings : test tape : tta?02 ?test point : tp8(lch), tp9(rch) ?input signal : 1khz (line in) method : apply a 1khz signal and rec mode. then adjust osc attenuator so that the output level at tp8, tp9 becomes 0vu. record and play back the 1khz signals and check that the output is ?db 3.0db. < front section > 14. -con osc adjustment settings : test point : tp7 and gnd ?adjustment location : l331 method : insert ac plug while pressing power and tuner function keys. adjust l331 so that the frequency at the test point is 153.84hz 0.15hz. 46 adjustment front c.b ic201 fl401 gnd tp7 16 l331 c326 1 r268 + 30 11 rev fwd deck-1 p head deck-2 r/p/e head 11 10 sfr1 deck c.b main c.b sfr451 sfr452 l801 tp2 (clk) tp4 (dc balance) gnd tp8 (rch) tp9 (lch) 10 2 l802 9 5 tp1 (vt) ffe831 tp3 (dc balance) 8 1 3 4 2 3 6 5 6 7 8 9 11 12 13 14 15 16 9 14 ic801 tc943 tc941 l941 l952 l953 l942 47 < tuner section > 1. clock frequency check settings : ?test point : tp2 method : set to wm 1602khz and check that the test point is 2052khz 45hz. 2. mw vt adjustment settings : ?test point : tp1 (vt) ?adjustment location : l953 method : set to mw 1710khz, 530khz and adjust l953 so that the test point is 8.0v 0.05v (1710khz) and more than 0.3v (530khz). 3. sw vt adjustment settings : ?test point : tp1 (vt) ?adjustment location : l942 method : set to sw 17.9mhz, 5.73mhz and adjust l942 so that the test point is 8.0v 0.05v (17.9mhz) and more than 0.3v (5.9mhz). 4. fm vt check settings : ?test point : tp1 (vt) method : set to fm 87.5mhz, 108.0mhz and check that the test point is more than 0.5v (87.5mhz) and less than 8.0v (108.0mhz). 5. mw tracking adjustment settings : test point : tp8(lch), tp9(rch) ?adjustment location : l952 ...................................... 603khz tc941 ...................................1404khz method : set to mw 603khz and adjust l952 so that the level at the test point becomes maximum. next, set to mw 1404khz and adjust tc941 so that the level at the test point becomes maximum. 6. sw tracking adjustment settings : test point : tp8(lch), tp9(rch) ?adjustment location : l941 ...................................... 5.9mhz tc943 ...................................17.9mhz method : set to sw 5.9mhz and adjust l941 so that the level at the test point becomes maximum. next, set to sw 17.9mhz and adjust tc943 so that the level at the test point becomes maximum. 7. fm tracking check settings : ?test point : tp8(lch), tp9(rch) method : set to fm 98.0mhz and check that the test point is less than 9db v. 8. am if adjustment settings : ?test point : tp8(lch), tp9(rch) ?adjustment location : l802 ............................................. 999khz 9. dc balance / mono distortion adjustment settings : ?test point : tp3, tp4 (dc balance) : tp8(lch), tp9(rch) (distortion) ?adjustment location : l801 ?input level : 60db v method : set to fm 98.0mhz and adjust l801 so that the voltage between tp3 and tp4 becomes 0v 0.3v. next, check that the distortion is less than 1.3%. < deck section > 10. tape speed adjustment (deck 2) settings : test tape : tta?00 ?test point : tp8(lch), tp9(rch) ?adjustment location : sfr1 method : play back the test tape and adjust sfr1 so that the frequency counter reads 3000hz 5hz and 45hz (rev) with respect to forward speed. 11. head azimuth adjustment (deck 1, deck 2) settings : test tape : tta?30 ?test point : tp8(lch), tp9(rch) ?adjustment location : head azimuth adjustment screw method : play back (fwd) the 8khz signal of the test tape and adjust screw so that the output becomes maximum. next, perform on rev play mode. 12. pb frequency response check (deck 1, deck 2) settings : test tape : tta?00 ?test point :tp8(lch), tp9(rch) method : play back the 315hz and 8khz signals of the test tape and check that the output ratio of the 8khz signal with respect to that of the 315hz signal is within 5db. 13. pb sensitivity check (deck 1, deck 2) settings : test tape : tta?00 ?test point : tp8(lch), tp9(rch) method : play back the test tape and check that the output level of the test point is 140mv 3db. 14. rec/pb frequency response adjustment (deck 2) settings : test tape : tta?02 ?test point : tp8(lch), tp9(rch) ?input signal : 1khz / 8khz (line in) ?adjustment location : sfr451 (lch) sfr452 (rch) method : apply a 1khz signal and rec mode. then adjust osc attenuator so that the output level at the tp8, tp9 becomes -20vu. record and play back the 1khz and 8khz signals and adjust sfrs so that the output of the 8khz signals becomes 0db 0.5db with respect to that of the 1khz signal. 15. rec/pb sensitivity check (deck 2) settings : test tape : tta?02 ?test point : tp8(lch), tp9(rch) ?input signal : 1khz (line in) method : apply a 1khz signal and rec mode. then adjust osc attenuator so that the output level at tp8, tp9 becomes 0vu. record and play back the 1khz signals and check that the output is ?db 3.0db. < front section > 16. -con osc adjustment settings : test point : tp7 and gnd ?adjustment location : l331 method : insert ac plug while pressing power and tuner function keys. adjust l331 so that the frequency at the test point is 153.84hz 0.15hz. 48 ref. no part no. kanri description no. ref. no part no. kanri description no. mechanical main parts list 1/1 color name table basic color symbol color basic color symbol color basic color symbol color b black c cream d orange g green h gray l blue lt transparent blue n gold p pink r red s silver st titan silver t brown v violet w white wt transparent white y yellow yt transparent yellow lm metallic blue ll light blue gt transparent green ld dark blue dt transparent orange gm metallic green ym metallic yellow dm metallic orange pt transparent pink 1 8a-nfj-012-010 window,cass 1 2 8a-nfj-013-010 window,cass 2 3 8a-nfj-035-010 box,cass 1h 4 8a-nfj-003-010 box,cass 2 u ! 44 87-a80-092-010 ac cord assy,e blk sun fai<4ez,6ez> ! 44 87-a80-155-010 ac cord assy,hs ts 50 49 mechanical exploded view 1/1 (hs,hr only) (k,4ez,6ez only) 2 3 5 6 8 9 9 4 1 10 12 7 11 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 33 33 35 35 36 37 48 47 38 wire,binder 39 40 41 p.c.b 42 43 44 45 46 d a i a a a a a a a a a f f g g a a a ht-sink fin 1 fin 2 ht-sink hs,hr only) ht-sink a a b b c a a a e f h h p.c.b azg-1 p.c.b chas ,main 2zm-3 (hs,hr only) 6zm-3 (k,4ez,6ez only) plate,earth mech plate,earth mic fl ht-sink a ( 52 51 mechanism exploded view 1/1 53 ref. no part no. kanri description no. ref. no part no. kanri description no. mechanism main parts list 1/1 54 mechanism main parts list 1/1 56 55 mechanism exploded view 1/1 58 57 ref. no part no. kanri description no. speaker (sx-wnbl56) <56ez> parts list fig-1 fig-2 fig-3 1 3 2 speaker disassembly instructions type.4 how to remove the panel, fr 1. insert the ( ?) flat head screwdriver tip into the gap between the panel, fr and the panel, spkr. tap the head of the ( ?) flat head screwdriver with the plastic hammer head, and create the clearance as shown in fig-1. 2. insert the cut chisel in the clearance, and tap the head of the cut chisel with plastic hammer as shown in fig-2, to remove the panel, fr. 3. place the speaker horizontally. tap head of the cut chisel with plastic hammer as shown in fig-3, and remove the panel, fr completely. how to attach the panel, fr attach the panel, fr to the panel, spkr. tap the four corners of the panel, fr with the plastic hammer to fit the panel, fr into the panel, spkr completely. type.1 insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. remove the screws of each speaker unit and then remove the speaker units. type.2 remove the grill frame and four pieces of rubber caps by pulling out with a flat-bladed screwdriver. remove the screws from hole where installed rubber caps. insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. re- move the screws of each speaker unit and then remove the speaker units. type.3 insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. turn the speaker unit to counter- clockwisedirection while inserting a flat-bladed screwdriver into one of the hollows around speaker unit, and then remove the speaker unit. after replacing the speaker unit, install it turning to clockwise direction until "click" sound comes out. tools 1 plastic head hammer 2 ( ?) flat head screwdriver 3 cut chisel 1 8a-ns5-016-010 panel,fr u 2 8a-ns5-017-010 plate,name b 3 8a-ns5-004-010 panel,duct 4 8a-ns5-009-010 protector, 5 8a-ns5-018-010 grille,frame assy rds 6 8a-ns5-015-010 badge,aiwa s35 7 8z-nsy-003-010 cord,bush 8 88-ns3-029-010 cord,bush l 9 88-ns5-610-010 cord,spkr 10 88-ns5-611-010 cord,spkr b/l 11 8z-nsy-608-010 spkr, ceramic assy 12 8a-ns8-604-010 spkr, m 100 13 8z-ns7-602-010 spkr, w 160 ref. no part no. kanri description no. speaker (sx-wnbl53) 2 11, ikenohata 1 chome, taito-ku, tokyo 110, japan tel:03 (3827) 3111 printed in singapore 920074 |
Price & Availability of NSX-BL54 | |
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |