![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
date : 2006/9/7 ampire co., ltd. 1 specifications for lcd module customer customer part no. ampire part no. AC-161JYILY-70 approved by date approved by checked by organized by a m p ire
date : 2006/9/7 ampire co., ltd. 2 record of revision revision date page contents editor 2006/6/7 2006/9/7 - 3 new release modify mechanical data tony sunglin date : 2006/9/7 ampire co., ltd. 3 1 features (1) display format : 16 characters 1 lines (2) construction : lcd panel, bezel, zebra ,yellow-green led back-light and pcb. (3) display type ; stn ,yellow-green mode , transflective, 6 o?clock view. (4) controller : st7066-0a. (5) 5v single power input. (6) normal temperature type. (7) rohs compliant. 2 mechanical data parameter stand value unit dot size 1.152 (w) 1.765(h) mm dot pitch 1.212(w) 1.825(h) mm character size 6.0(w) 14.54(h) mm viewing area 120.0(w) 23.0(h) mm module size 151.0(w) 40.0(h) 14.7 max (t) mm 3 absolute maximum ratings parameter symbol min max unit logic circuit supply voltage vdd-vss -0.3 7.0 v lcd driving voltage vdd-vo -0.3 10.0 v input voltage v i -0.3 vdd+0.3 v operating temp. t op 0 50 c normal temp. type storage temp. t stg -20 70 c date : 2006/9/7 ampire co., ltd. 4 4 electro-optical characteristics parameter symbol condition min typ max unit note ----- electronic characteristics ----- logic circuit supply voltage vdd-vss -- 2.7 -- 5.5 v 0 c -- -- -- 25 c 4.75 5.0 5.25 lcd driving voltage ( stn ) vdd-vo 50 c -- -- -- v 0 ~ 50 c for normal temp. type vih -- 0.7 vdd -- vdd v input voltage vil -- vss -- 0.3 vdd v logic supply current idd vdd = 5v -- 2.0 2.4 ma ----- optical characteristics ( stn ) ----- contrast cr 25 c -- 5 -- note 1 rise time tr 25 c -- 200 300 ms fall time tf 25 c -- 200 300 ms note 2 f -- 40 -- b -- 35 -- l -- 35 -- viewing angle range r 25 c & cr 2 -- 35 -- deg. note 3 frame frequency ff 25 c -- 64 -- hz -----array type led back-light characteristics ----- parameter symbol condition min typ max unit note forward voltage vf -- -- 4.05 4.3 v supply voltage between a&k forward current if vf=4.05v -- 420 -- ma lcm luminous intensity vf=4.05v -- 30 -- cd/m 2 a k * led dice number = 2 42 =84 date : 2006/9/7 ampire co., ltd. 5 (note 1) contrast ratio :cr = (brightness in off state) / (brightness in on state) ( note 2 ) response time : (note 3) viewing angle date : 2006/9/7 ampire co., ltd. 6 5 block diagram & power supply 16 character x 1 line com1 com8 seg1 ~ seg40 com9 st7066 com16 e r/w rs db0~db7 vdd vo vss interface lcd module vo vdd(+5v) r1 r2 vr vss 5v power input lcd bias circuit led-backlight a k 4.05v date : 2006/9/7 ampire co., ltd. 7 6 interface no. symbol function 1 vss ground (0v) 2 vdd supply voltage for logic (+5v ) 3 vo contrast adjustment 4 rs data/instruction select 5 r/w read/write select 6 e enable signal 7 db0 data bus 8 db1 data bus 9 db2 data bus 10 db3 data bus 11 db4 data bus 12 db5 data bus 13 db6 data bus 14 db7 data bus date : 2006/9/7 ampire co., ltd. 8 7 timing characteristics write operation vdd=5v vdd=3.3v item symbol min max min max unit enable cycle time t cyce 500 -- 1000 -- enable pulse width pw eh 230 -- 450 -- enable rise/fall time t er ,t ef -- 20 -- 25 address set-up time (rs, r/w to e) t as 40 -- 60 -- address hold time t ah 10 -- 20 -- data set-up time t dsw 80 -- 195 -- data hold time t h 10 -- 10 -- ns date : 2006/9/7 ampire co., ltd. 9 read operation vdd=5v vdd=3.3v item symbol min max min max unit enable cycle time t cyce 500 -- 1000 -- enable pulse width pw eh 230 -- 450 -- enable rise/fall time t er ,t ef -- 20 -- 25 address set-up time (rs, r/w to e) t as 40 -- 60 -- address hold time t ah 10 -- 20 -- data delay time t ddr -- 120 -- 360 data hold time t drh 5 -- 5 -- ns date : 2006/9/7 ampire co., ltd. 10 8 instruction set code instruction rs r/ w d7 d6 d5 d4 d3 d2 d1 d0 description e.t.(f osc =270 khz) clear display 0 0 0 0 0 0 0 0 0 1 write?20h? to ddram and set ddram address to ?00h? from ac 1.53 ms return home 0 0 0 0 0 0 0 0 1 -- sets dd ram address to ?00h? from ac and return cursor to its original position if shifted. the contents of ddram are not changed. 1.53 ms entry mode set 0 0 0 0 0 0 0 1 i/d sh assign cursor moving direction and enable the shift of entire display. 39 s display on/off control 0 0 0 0 0 0 1 d c b set display (d), cursor (c), and blink of cursor (b) on/off control bit. 39 s cursor or display shift 0 0 0 0 0 1 s/ c r/ l -- -- set cursor moving and display shift control bit, and the direction, without changing of ddram data. 39 s function set 0 0 0 0 1 dl n f -- -- sets interface data length (dl:8-bit/4-bit), number of display lines (n:2-line/1-line) and , display font type (f:5x11dots/5x8 dost). 39 s set cg ram address 0 0 0 1 ac 5 ac 4 ac 3 ac 2 ac 1 ac 0 sets cg ram address in address counter. 39 s set dd ram address 0 0 1 ac 6 ac 5 ac 4 ac 3 ac 2 ac 1 ac 0 sets dd ram address in address counter. 39 s read busy flag and address 0 1 bf ac 6 ac 5 ac 4 ac 3 ac 2 ac 1 ac 0 whether during internal operation or not can be known by reading bf. the contents of address counter can also be read. 0 s write data to ram 1 0 d7 d6 d5 d4 d3 d2 d1 d0 writes data into internal ram (dd ram /cg ram). 43 s read data from ram 1 1 d7 d6 d5 d4 d3 d2 d1 d0 reads data from internal ram (dd ram /cg ram). 43 s * ?--? : don?t care note : when an mpu program with checking the busy flag(db7) is made, it must be necesssary1/2fosc is necessary for executing the ne xt instruction by the falling edge of the ?e? signal after the busy flag(db7) goes to ?low?. date : 2006/9/7 ampire co., ltd. 11 9 initialization sequence 10 dd ram address digit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 line 00 01 02 03 04 05 06 07 40 41 42 43 44 45 46 47 display position dd ram address date : 2006/9/7 ampire co., ltd. 12 11 font table date : 2006/9/7 ampire co., ltd. 13 12 quality and reliability 12.1 test conditions tests should be conducted under the following conditions : ambient temperature : 25 5 c humidity : 60 25% rh. 12.2 sampling plan sampling method shall be in accord ance with mil-std-105e , level ii, normal single sampling plan . 12.3 acceptable quality level a major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. a minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bear ing on its effective use or operation. 12.4 appearance an appearance test should be conducted by human sight at approximately 30 cm distance from the lcd module under flourescent light. the inspection area of lcd panel shall be within the range of following limits. date : 2006/9/7 ampire co., ltd. 14 12.5 inspection quality criteria item description of defects class of defects acceptable level (%) function short circuit or pattern cut major 0.65 dimension deviation from drawings major 1.5 ave . dia . d area a area b d 0.2 disregard 0.2 date : 2006/9/7 ampire co., ltd. 15 12.6 reliability test item test conditions note high temperature operation 50 3 c , t=96 hrs low temperature operation 0 3 c , t=96 hrs high temperature storage 70 3 c , t=96 hrs 1,2 low temperature storage -20 3 c , t=96 hrs 1,2 temperature cycle -20 c ~ 25 c ~ 70 c 30 m in. 5 min. 30 min. ( 1 cycle ) total 5 cycle 1,2 humidity test 40 c, humidity 90%, 96 hrs 1,2 vibration test (packing) sweep frequency : 10 ~ 55 ~ 10 hz/1min amplitude : 0.75mm test direction : x.y.z/3 axis duration : 30min/each axis 2 note 1 : condensation of wate r is not permitted on the module. note 2 : the module should be inspected after 1 hour storage in normal conditions (15-35c , 45-65%rh). definitions of life end point : z current drain should be smalle r than the specific value. z function of the module should be maintained. z appearance and display quality should not have degraded noticeably. z contrast ratio should be greater than 50% of the initial value. date : 2006/9/7 ampire co., ltd. 16 13 handling precautions (1) a lcd module is a fragile item and should not be subjected to strong mechanical shocks. (2) avoid applying pressure to the module surfa ce. this will distort the glass and cause a change in color. (3) under no circumstances should the position of th e bezel tabs or their shape be modified. (4) do not modify the display pcb in either shape or positioning of components. (5) do not modify or move location of the zebra or heat seal connectors. (6) the device should only be soldered to during interfacing. modification to other areas of the board should not be carried out. (7) in the event of lcd breakage and resultant leak age of fluid do not inhale, ingest or make contact with the skin. if contact is made rinse immediately. (8) when cleaning the module use a soft damp cloth with a mild solvent, such as isopropyl or ethyl alcohol. the use of water, ke tone or aromatic is not permitted. (9) prior to initial power up input signals should not be applied. (10) protect the module against st atic electricity and observ e appropriate anti-static precautions. date : 2006/9/7 ampire co., ltd. 17 14 outline dimension ? t 1 a? 1q |
Price & Availability of AC-161JYILY-70
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |