View ET035009DH6_41553.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EXAMINED www..com
BY :
FILE NO .
CAS-0006273
EMERGING DISPLAY
APPROVED BY: TECHNOLOGIES CORPORATION
ISSUE :
SEP.12, 2007 30
TOTAL PAGE : VERSION :
1
CUSTOMER
ACCEPTANCE
SPECIFICATIONS
M OD EL
NO . :
ET035009DH6 (R oHS)
FOR M ESSRS :
CUSTOMER'S APPROVAL
: _____________________________
DATE BY : _____________________________
02101300-01-02
www..com
EMERGING
RECORDS
DATE
DISPLAY
REVISION
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
DOC . FIRST ISSUE
1
0-1
SEP.12, 2007
OF
REVISED PAGE NO.
SUMMARY
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
0-2
TABLE
OF
CONTENTS
NO. ITEM PAGE ===============================================================
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 12. GENERAL SPECIFICATIONS
--------------------------------------------------------------------------------------------------------------------------------------------------------
1 1 2 3 4~6 7,8 9 10 11 12 , 13 14 15 ~ 20 21 ~ 30
MECHANICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS TIMING CHART OPTICAL CHARACTERISTICS OUTLINE DIMENSIONS BLOCK DIMENSIONS
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DETAIL DRAWING OF DOT MATRIX INTERFACE SIGNAL POWER SUPPLY
TOUCH PANEL SPECIFICATION
SPECIFICATION OF AUDACITY ASSURANCE
02101300-01-02
www..com
EMERGING
1.
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION GENERAL SPECIFICATIONS 1.1
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
1
APPLICATION NOTES FOR CONTROLLER/DRIVER PLEASE REFER TO : HX8238-A
1.2
MATERIAL SAFETY DESCRIPTION ASSEMBLIES SHALL COMPLY WITH EUROPEAN ROHS REQUIREMENTS, INCLUDING PROHIBITED MATERIALS/COMPONENTS CONTAINING LEAD, MERCURY, CADMIUM, HEXAVALENT CHROMIUM, POLYBROMINATED BIPHENYLS (PBB) AND POLYBROMINATED DIPHENYL ETHERS (PBDE)
2.
MECHANICAL SPECIFICATIONS
( 1 ) DISPLAY SIZE (inch) ( 2 ) NUMBER OF DOTS ( 3 ) MODULE SIZE ( 4 ) EFFECTIVE AREA ( 5 ) ACTIVE AREA ( 6 ) DOT SIZE ( 7 ) PIXEL SIZE ( 8 ) LCD TYPE ( 9 ) COLOR
-------------------------- 3.5" -------------------------- 320W * (RGB) * 240H DOTS
(WITHOUT FPC)
-------------------------------- 76.8W * 63.8H * 4.4(D) mm --------------------------- 72.2W*54.76H mm (T/P) -------------------------------- 70.08W * 52.56H mm (LCD)
70.8W * 53.26H mm (T/P)
------------------------------------- 0.073W * 0.219H mm ------------------------------------- 0.219W * 0.219H mm ------------------------------------- TFT , TRANSMISSIVE ------------------------------------- 262K (24BIT) ------------------------ 6 O'CLOCK ------------------------------------ LED , COLOR : WHITE
( 10 ) VIEWING DIRECTION ( 11 ) BACK LIGHT
02101300-01-02
www..com
EMERGING
3.
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
2
ABSOLUTE MAXIMUM RATINGS 3.1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS .
PARAMETER SYMBOL VDD VCC PD IF VR MIN. VSS-0.3 -0.3 MAX. 5.0 4.0 540 25 30 UNIT V V mW mA V REMARK
POWER VOLTAGE POWER DISSIPATION FORWARD CURRENT REVERSE VOLTAGE
3 . 2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS .
ITEM AMBIENT TEMPERATURE HUMIDITY OPERATING MIN. -10C MAX. 60C STORAGE MIN. -20C MAX. 70C REMARK NOTE ( 1 ), ( 2 ) WITHOUT CONDENSATION 5~20Hz , 1HR 20~500Hz(20Hz) , 1HR 20~500Hz(500Hz) , 1HR X,Y,Z,TOTAL 3HR 10 m SECONDS XYZ DIRECTIONS 1 TIME EACH
NOTE ( 3 ) 2.45m/s2 ( 0.25G)
NOTE ( 3 ) 11.76m/s2 ( 1.2G )
VIBRATION
SHOCK
29.4m/s ( 3G)
2
490m/s ( 50G )
2
CORROSIVE GAS
NOT ACCEPTABLE
NOT ACCEPTABLE
NOTE ( 1 ) : Ta AT -20C : 48HR MAX . 70C : 168HR MAX . NOTE ( 2 ) : BACKGROUND COLOR CHANGES SLIGHTLY DEPENDING ON AMBIENT TEMPERATURE THIS PHENOMENON IS REVERSIBLE . NOTE ( 3 ) : Ta 60C : 90%RH MAX (96HRS MAX). Ta > 60C : ABSOLUTE HUMIDITY MUST BE LOWER THAN THE HUMIDITY OF 90%RH AT 60C(96HRS MAX).
02101300-01-02
www..com
EMERGING
4.
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
3
Ta = 25 C REMARK
ELECTRICAL CHARACTERISTICS
PARAMETER SYMBOL CONDITION VCC VDD MIN. 2.5 2.5 TYP. 3.3 3.3 (1) (10) 20.4 40k MAX. 3.6 3.6 (2) (15) VCC 0.1*VCC VCC 0.2*VCC 21.6 UNIT V V mA mA V V V V V hr NOET(1)
DIGITAL POWER SUPPLY ANALOG POWER SUPPLY DIGITAL OPERATING CURRENT ANALOG OPERATING CURRENT LOGIC HIGH OUTPUT VOLTAGE LOGIC LOW OUTPUT VOLTAGE LOGIC HIGH INPUT VOLTAGE LOGIC LOW INPUT VOLTAGE FORWARD VOLTAGE LED LIFE TIME
ICC IDD
VOH VOL VIH VIL VF
IOUT=-100A 0.9*VCC IOUT=100A
H LEVEL L LEVEL IF=20mA 0 0.8*VCC 0 19.2 30k
NOET(1) : INTERNAL CIRCUIT DIAGRAM OF BACKLIGHT
02101300-01-02
www..com
EMERGING
5.
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION TIMING CHART 5.1
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
4
DIGITAL PARALLEL RBG INTERFACE
SYMBOL fDCLK tDCLK tvsys tvsyh thsys tvsyh thv tCKL tCKH tds tdh tRES MIN. 100 20 20 20 20 1 50 50 12 12 10 TYP. 6.5 154 MAX. 10 240 UNIT MHz ns ns ns ns ns
tDCLK
CHARACTERISTICS DCLK FREQUENCY DCLK PERIOD VERTICAL SYNC SETUP TIME VERTICAL SYNC HOLD TIME HORIZONTAL SYNC SETUP TIME HORIZONTAL SYNC HOLD TIME PHASE DIFFERENCE OF SYNC SIGNAL FALLING EDGE DCLK LOW PERIOD DCLK HIGH PERIOD DATA SETUP TIME DATA HOLD TIME RESET PULSE WIDTH
ns ns ns ns s
02101300-01-02
www..com
EMERGING
5.2
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
5
PARALLEL RGB INTERFACE (SYNC MODE)
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
6
CHARACTERISTICS DCLK FREQUENCY DCLK PERIOD HORIZONTAL FREQUENCY (LINE) VERTICAL FREQUENCY (REFRESH) HORIZONTAL BACK PORCH HORIZONTAL FRONT PORCH HORIZONTAL DATA START POINT HORIZONTAL BLANKING PERIOD HORIZONTAL DISPLAY AREA HORIZONTAL CYCLE VERTICAL BACK PORCH VERTICAL FRONT PORCH VERTICAL DATA START POINT VERTICAL BLANKING PERIOD NTSC VERTICAL DISPLAY AREA PAL VERTICAL CYCLE NTSC PAL
SYMBOL
fDCLK tDCLK fH fV tHBP tHFP tHBP tHBP + tHFP HDISP Hcycle tVBP tVFP tVBP tVBP + tVFP VDISP Vcycle
MIN. 100
TYP. 6.5 154 14.9 60 68 20 68 88 320 408 18 4 18 22 240
280(PALM=0) 280(PALM=1)
MAX. 10 22.35 90 450 350
MHz ns KHz Hz tDCLK tDCLK tDCLK tDCLK tDCLK tDCLK Lines Lines Lines Lines Lines Lines
262 313
02101300-01-02
www..com
EMERGING
6.
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
7
OPTICAL CHARACTERISTICS (NOTE1) 6.1 OPTICAL CHARACTERISTICS
Ta = 2 5 2C ITEM SYMBOL y+ yx+ xCR tr(rise) tf(fall) B X Y X Y X Y X Y x=0 , y=0 IF=20mA NTSC(60)% CONDITION x=0 CR 10 y=0 x=0 , y=0 x=0 , y=0 x=0 , y=0 IF=20mA MIN. (50) (70) (70) (70) (300) (300) TYP. (55) (75) (75) (75) (400) 15 35 (400) MAX. 20 50 msec cd/m2 % (3) (4) (5) deg. (2) , (3) UNIT REMARK
VIEWING ANGLE
CONTRAST RATIO RESPONSE TIME THE BRIGHTNESS OF MODULE WHITE RED GREEN BLUE THE UNIFORMITY OF BRIGHTNESS
(0.236) (0.286) (0.336) (0.261) (0.311) (0.361) (0.562) (0.612) (0.662) (0.305) (0.355) (0.405) (0.262) (0.312) (0.362) (0.533) (0.583) (0.633) (0.090) (0.140) (0.190) (0.020) (0.070) (0.120) (70)
COLOR OF CIE COORDINATE
(6)
NOTE (1) : TEST EQUIPMENT SETUP : AFTER STABILIZING AND LEAVING THE PANEL ALONE AT A GIVEN TEMPERATURE FOR 30 MINUTES , THE MEASUREMENT SHOULD BE EXECUTED. MEASUREMENT SHOULD BE EXECUTED IN A STABLE , WINDLESS , AND DARK ROOM. OPTICAL SPECIFICATIONS ARE MEASURED BY TOPCON BM-7 (FAST) WITH A VIEWING ANGLE OF 2 AT A DISTANCE OF 50cm AND NORMAL DIRECTION.
7)
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
NOTE (2) : DEFINITION OF VIEWING ANGLE :
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
8
x = y = 0 y+
yxx-
x+
y-
6 o'clock direction
y-
x+
NOTE (3) : DEFINITION OF CONTRAST RATIO : BRIGHTNESS MEASURED WHEN LCD IS AT " WHITE STATE" CONTRASTRA TIO(CR ) = BRIGHTNESS MEASURED WHEN LCD IS AT " BLACK STATE" NOTE (4) : DEFINITION OF RESPONSE TIME : TR AND TF THE FIGURE BVELOW IS THE OUTPUT SIGNAL OF THE PHOTO DETECTOR. (T%)
White
Black
White
NOTE (5) : BRIGHTNESS MEASURED WHEN LCD IS AT " WHITE STATE" NOTE (6) : THE 100% TRANSMISSION IS DEFINED AS THE TRANSMISSION OF LCD PANEL WHEN ALL THE INPUT TERMINALS OF MODULE ARE ELECTRICALLY OPENED.
6.2
THE TEST METHOD OF BRIGHTNESS AND UNIFORMITY
VF
UNITmm
6.3
THE CALCULATING METHOD OF UNIFORMITY
MAXIMUN BRIGHTESS - MINIMUN BRIGHTESS UNIFORMITY : 1 - x 100% AVERAGE BRIGHTESS
02101300-01-02
www..com
EMERGING
7. OUTLINE DIMENSIONS
DISPLAY
MODEL NO.
E T 0 3 5 0 0 9 D H 6 (RoHS)
VERSION
PAGE
TECHNOLOGIES C O R P O R A T I O N
1
9
UNIT : mm SCALE : NTS NOT SPECIFIED LENGTH TOLERANCE IS 0.5 NOT SPECIFIED ANGLE TOLERANCE IS 2
02101300-01-02
www..com
EMERGING
8.
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION BLOCK DIMENSION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
10
02101300-01-02
www..com
EMERGING
9.
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
11
DETAIL DRAWING OF DOT MATRIX
70.08 0.219 0.073 0.219
R R GB GB
52.56
320(RGB)*240 PIXEL
RG
B
UNIT : mm SCALE : NTS NOT SPECIFIED TOLERANCE IS 0.1 DOTS MATRIX TOLERANCE IS 0.01
02101300-01-02
www..com
EMERGING
10 .
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION INTERFACE SIGNALS
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
12
PIN NO SYMBOL I/O 1 VBLP 2 VBLP 3 VBL+ P 4 VBL+ P 5 NC 6 /RESET I 7 CSB I 8 SCK I 9 SDI I 10 SDO O 11 B7 I 12 B6 I 13 B5 I 14 B4 I 15 B3 I 16 B2 I 17 B1 I 18 B0 I 19 G7 I 20 G6 I 21 G5 I 22 G4 I 23 G3 I 24 G2 I 25 G1 I 26 G0 I 27 R7 I 28 R6 I 29 R5 I 30 R4 I 31 R3 I 32 R2 I 33 R1 I 34 R0 I
FUNCTION BACKLIGHT LED GROUND (K) BACKLIGHT LED GROUND (K) BACKLIGHT LED POWER (A) BACKLIGHT LED POWER (A) NOT USE HARDWARE RESET SPI INTERFACE CHIP SELECT BAR SPI INTERFACE DATA CLOCK SPI INTERFACE DATA (INPUT) SPI INTERFACE DATA(OUTPUT) BLUE DATA BIT 7 BLUE DATA BIT 6 BLUE DATA BIT 5 BLUE DATA BIT 4 BLUE DATA BIT 3 BLUE DATA BIT 2 BLUE DATA BIT 1 BLUE DATA BIT 0 GREEN DATA BIT 7 GREEN DATA BIT 6 GREEN DATA BIT 5 GREEN DATA BIT 4 GREEN DATA BIT 3 GREEN DATA BIT 2 GREEN DATA BIT 1 GREEN DATA BIT 0 RED DATA BIT 7 RED DATA BIT 6 RED DATA BIT 5 RED DATA BIT 4 RED DATA BIT 3 RED DATA BIT 2 RED DATA BIT 1 RED DATA BIT 0
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
13
PIN NO SYMBOL I/O FUNCTION 35 DCLK I DOT DATA COLCK 36 HSYNC I HORIZONTAL SYNC INPUT 37 VSYNC I VERTICAL SYNC INPUT 38 ENB I DATA ENABLE INPUT 39 VDD P ANALOG POWER 40 VDD P ANALOG POWER 41 VCC P DIGITAL POWER 42 VCC P DIGITAL POWER 43 YU I TOP PANEL 44 XR I RIGHT PANEL TOUCH PANEL INTERFACE SIGNALS 45 YD I BOTTOM PANEL 46 XL I LEFT PANEL 47 48 49 50 SHUT NC VSS VSS I P P
DISPLAY SHUT DOWN PIN TO PUT THE DRIVER INTO SLEEP MODE. CONNECT TO VCC FOR SLEEP MODE. CONNECT TO VSS FOR NORMAL OPERATING MODE.
NOT USE GROUND GROUND
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION 1 1 . POWER SUPPLY 1 1 .1 POWER SUPPLY FOR LCM
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
14
VDD VCC
3.3V
3.3V
VSS
IF = 20mA (A) VBL+ LED (K) VBLTOUCH PANEL VF=20.4V
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
15
12 . TOUCH PANEL SPECIFICATION 12.1 ELECTRICAL CHARACTERISTICS
ITEM LINEARITY TERMINAL RESISTANCE INSULATION RESISTANCE CONDITION X AXIS Y AXIS DC25V MIN. -10C -20C SPEC. 1.5 200 ~ 900 200 ~ 900 20 TYP. 5
Ta = 25C
UNIT % M MAX. 60C +70C
12.2
ABSOLUTE MAXIMUM RATINGS :
ITEM OPERATING TEMPERATURE (Top) STORAGE TEMPERATURE (Tst) INPUT VOLTAGE ( V )
12.3 PRECAUTIONS IN USE OF TOUCH PANEL 12.3.1 PURPOSE IN ORDER TO PREVENT ACCIDENTAL USE AND PERFORMANCE DETERIORATION, PLEASE KEEP THE FOLLOWING PRECAUTIONS AND INHIBITED POINTS. 12.3.2 ITEM AND ILLUSTRATION ( 1 ) STRUCTURE, AREA DEFINITION THE STRUCTURE AND THE PERFORMANCE GUARANTEED AREA OF THIS TOUCH PANEL ARE DEFINED BELOW
THE ABOVE FIGURE IS OUR DESIGN RULE OF TOUCH PANEL. IF IT CANNOT MEET YOUR REQUIREMENT, PLEASE CONTACT WITH OUR ENGINEERS FOR FURTHER DISCUSSION. ABOVE FIGURE ILLUSTRATES THE RECOMMENDED BEZEL AND CUSHION DESIGN. IN ORDER TO PREVENT UNUSUAL PERFORMANCE DEGRADATION AND MALFUNCTION OF A TOUCH PANEL, PLEASE CARRY OUT THE SET CASE DESIGNING AND A TOUCH PANEL ASSEMBLING METHOD AFTER SURELY CONSIDERING THE DEFINITION OF EACH AREA ILLUSTRATED IN ABOVE FIGURE.
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
16
AREA(a)ACTIVE AREA THE ACTIVE AREA IS GUARANTEED THE POSITION DATA DETECTABLE PRECISION, OPERATION FORCE AND OTHER OPERATIONS. IT IS STRONGLY RECOMMENDED TO PLACE THE OPERATION BUTTON OR MENU KEYS WITHIN THE ACTIVE AREA. DUE TO STRUCTURE, THE ACTIVE AREA IS LESS DURABLE AT THE EDGE OR CLOSE TO THE EDGE. AREA(b)OPERATION NON-GUARANTEED AREA THIS AREA DOES NOT GUARANTEE A TOUCH PANEL OPERATION AND ITS FUNCTION. WHEN THIS AREA IS PRESSED, TOUCH PANEL SHOWS DEGRADATION OF ITS PERFORMANCE AND DURABILITY SUCH AS A PEN SLIDING DURABILITY BECOMES ABOUT ONE-TENTH COMPARED WITH THE ACTIVE AREA (AREA-(A) AS GUARANTEED AREA) AND ITS OPERATION FORCE REQUIRES ABOUT DOUBLE. ABOUT 0.5 MM OUTSIDE FROM A BOUNDARY OF THE ACTIVE AREA CORRESPONDS TO THIS AREA. AREA(c)PRESSING PROHIBITION AREA THE AREA WHICH FORBIDS PRESSING, BECAUSE AN EXCESSIVE LOAD IS APPLIED TO A TRANSPARENT ELECTRODE (ITO) AND A SERIOUS DAMAGE IS GIVEN TO A TOUCH PANEL FUNCTION BY PRESSING. AREA(d)NON-ACTIVE AREA THE AREA DOES NOT ACTIVATE EVEN IF PRESSED. ( 2 ) CAUTIONS FOR INSTALLING AND ASSEMBLING ( i ) DO NOT GIVE EXCESSIVE STRAIN TO THE PRODUCT. ( ii ) FLEXIBLE PATTERN CABLE IS CONNECTED TO THE BODY BY THERMAL PRESSURE METHOD. SO, DO NOT APPLY EXCESSIVE FORCES TO THE FLEXIBLE PATTERN. DO NOT ADD AN EXCESSIVE FORCE TO A FPC(FLEX TAIL) THAT MAKES PEELING OFF OF THE FPC FROM THE PRODUCT. DO NOT FIX, ADHERE OR MOUNT ANY ADDITIONAL GOODS ON THE FPC SUCH AS ADDITIONAL FILM/PLATE ON THE FPC, BECAUSE SUCH ADDITIONAL GOODS WILL APPLY A STRESS AT THE FPC BONDING AREA. IT MAY AFFECT THE CONDUCTIVITY OF FPC WITH TOUCH PANEL. ( iii ) IN ORDER NOT TO APPLY LOAD ON THE DISPLAY, PROVIDE A CLEARANCE OF AT LEAST 0.3MM BETWEEN THE PRODUCT AND DISPLAY. ( iv ) WE RECOMMEND THE DESIGN OF A CASE OR BEZEL SHOULD COVERS THE BOUNDARY OF THE ACTIVE AREA INSIDE IN ORDER TO PREVENT AN OPERATION AT OUTSIDE OF THE ACTIVE AREA WHICH CAN NOT GUARANTEE THE FUNCTION OR DURABILITY (REFER TO ITEM 5.1.2. STRUCTURE, AREA DEFINITION). BEZEL'S EDGE PART MAY GUIDE THE PEN SLIDING ON THE SAME POSITION REPEATEDLY. IF THE BEZEL IS PLACED OUTSIDE OF THE ACTIVE AREA, IT MAY CAUSE THE DAMAGE OF THE ITO FILM.
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
17
( v ) PRESSING INSIDE OF BOUNDARY OF THE FRAME(PART (A) AS SHOWN IN BELOW) MAY CAUSES FAULT OPERATION, SO PLEASE DESIGN TO AVOID PRESSING OF TOUCH PANEL AT PART (A) SUCH AS HAVING GASKET/CUSHION AT PART (C). PARTICULARLY THE AREA (B) SHALL BE FREE FROM BURR. THE GASKET/CUSHION MATERIAL AT THE PART (C) SHOULD NOT BE EXCEEDED TO INSIDE OF THE BOUNDARY OF THE FRAME.
( vi ) TO PREVENT GIVING DISTORTION TO THE FILM OF THE PRODUCT AND PEELING OFF OF THE FILM FROM THE PRODUCT, DO NOT FIX THE FILM AND A SET CASE OR A SHOCK ABSORBING MATERIAL ADHERED TO A SET CASE BY ADHESION. (vii) WIPE OFF THE STAIN ON THE PRODUCT BY USING SOFT CLOTH MOISTENED WITH ETHANOL. TAKE CARE NOT TO ALLOW ETHANOL TO SOAK INTO THE JOINT OF UPPER FILM AND BOTTOM GLASS. IT MAY OTHERWISE CAUSE PEELING OR DEFECTIVE OPERATION. DO NOT USE ANY ORGANIC SOLVENT OR DETERGENT OTHER THAN ETHANOL. (viii) THE CORNERS OF THE PRODUCT ARE NOT CHAMFERED AND ARE SHARP. WHEN POSITIONING AND FIXING THE PRODUCT ON THE CASE, PROVIDE A ROUND PART ON THE CORNER OF THE CASE SO AS NOT TO APPLY LOAD ON THE CORNER OF THE TRANSPARENT TOUCH PANEL. (ix) DO NOT PRESS THE FILM OF THE PRODUCT WHEN THIS PRODUCT IS BUILT INTO A SET. ( 3 ) CAUTIONS FOR OPERATION (i) OPERATE IT WITH A POLYACETAL PEN (TIP R0.8 OR OVER) OR A BELLY OF A FINGER WITHOUT APPLYING EXCESSIVE LOAD. NEVER USE ANY MECHANICAL PENCILS, BALL POINT PENS AND HARD FINGERTIPS WHOSE TIP IS HARD FOR INPUT, OTHERWISE MALFUNCTIONS MAY RESULT.
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO.
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
18
(ii) THE INPUT POSITION MAY BE FLUCTUATED A LITTLE THROUGH LONG-TIME USE. IT IS DESIRABLE TO PROVIDE A ZERO-ADJUSTMENT FUNCTION BY USING A CIRCUIT AND SOFTWARE. (iii) OPERATION AT THE OUT OF ACTIVE AREA IS OUT OF OUR GUARANTEE. IT CAUSES A SERIOUS DAMAGE OF A TRANSPARENT ELECTRODE. DO NOT OPERATE AT THE OUT OF ACTIVE AREA. (iv) IN CASE OF CLEANING THE PART OF THE CASE BOUNDARY OF ACCOMPLISHED SET, USE A SOFT CLOTH WITH A FINGER BERRY OR A COTTON BUD. DO NOT CLEAN WITH A THI NG OTHER THAN THE FINGER SUCH AS HARD OR SHARP EDGES LIKE A FINGER NAIL ETC. ON THE CLOTH, BECAUSE IT CAUSE TRANSPARENT CONDUCTIVE FILM CRACKS. PLEASE ADVISE THIS PROHIBITION TO YOUR LAST CUSTOMERS. 12.4 DURABILITY 12.4.1 STYLUS HITTING ONE MILLION TIMES OR OVER NO DAMAGE ON FILM SURFACE PENR8 mm SILICON RUBBER LOAD250g FREQUENCY240 times/min MEASUREMENT POSITION: 1 POINT OF TOUCH PANEL ACTIVE AREA REPEATEDOVER 1,000,000 TIMES 12.4.2 PEN TOUCH SLIDING DURABILITY 100,000 TIMES OR OVER WRITING WITH R0.8mm PLASTIC STYLUS PEN; WRITING FORCE 150g IN ACTIVE AREA. SPEED IS 60mm/sec.
02101300-01-02
www..com
EMERGING
12.5
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
19
STEEL BALL DROP TEST BY USING F9mm STEEL BALL FROM THE HEIGHT OF 30cm AND FALLING ON TOUCH PANEL SURFACE, MUST PASS BELOW CONDITIONS APPEARANCETHE APPEARANCE WITHOUT ANY CHANGE, INCLUDING THE PANEL BROKEN.
12.6
APPEARANCE INSPECTION PURPOSE TO ESTABLISH APPEARANCE STANDARD AND MAINTAIN PRODUCT QUALITY SCOPE TOUCH PANEL VIEW AREA WITHIN TOUCH PANEL
12.6.1
RULE INSPECTION CONDITION (A) ENVIRONMENTAL LUMINANCE500 LUX (B) DISTANCE BETWEEN HUMAN EYES AND PANEL30 CM (PANEL MUST BE TESTED UNDER LIGHT TRANSPARENT) (C) VISUAL ANGEL > 60 (D) LIGHT SOURCE FLUORESCENT LIGHT SOURCE 12.6.2 JUDGE CRITERION JUDGEMENT UNDER ABOVE MENTIONED CRITERION (PANEL MUST BE TESTED UNDER LIGHT TRANSPARENT), TESTING GOODS DEFECT CAN BE VISIBLE WITHIN 10 SECONDS, WHICH WILL BE JUDGED AS MAJOR DEFECTS SAMPLING STANDARD THE SAMPLING STANDARD WILL BE CONFIRMED BY BOTH OF EDT AND CUSTOMER.
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
20
INSPECTION ITEMS
SEPC. W 0.1mm & L10mm W > 0.1mm or L > 10mm
JUDGE CRITERION ACCEPTABLE NOT ACCEPTABLE ACCEPTABLE NOT ACCEPTABLE
OPERATION GUIDELINE
SCRATCH
LINEAR FOREIGN OBJECT
W 0.1mm & L 5mm W > 0.1mm or L >5mm
GRANULAR FOREIGN OBJECT
D 0.3mm
ACCEPTABLE
D >0.3mm D 0.6mm PET BUBBLES D >0.6mm X 3mm CORNER Y 3mmZ < t (t = /thickness) EDGE W 3mm Y 3mmZ < t
NOT ACCEPTABLE ACCEPTABLE NOT ACCEPTABLE
CHIP ON GLASS
ACCEPTABLE
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
21
1 3 . SPECIFICATION OF AUDACITY ASSURANCE 13.1 APPLICATION This inspection standard is to be applied to the LCD module delivered from EMERGING DISPLAY TECHNOLOGIES CORP.( E.D.T ) to customers 13.2 INSPECTION CONDITIONS 13.2.1 (1)Observation Distance : 35cm5cm (2)View Angle : Non-operation Condition : 5(perpendicular to LCD panel surface) Operation Condition : 45 (perpendicular to LCD panel surface)
13.2.2 Environment Conditions : Ambient Temperature Ambient Humidity Ambient Cosmetic Inspection Illumination Functional Inspection 13.2.3 Inspection lot Quantity per delivery lot for each model
20C~25C 6520%RH More than 600Lux 300~500 Lux
13.2.4 Inspection method A sampling inspection shall be made according to the following provisions to judge The acceptability (a)Applicable standard : MIL-STD-105E Normal inspection , single sampling Level (b)AQL : Major defect : AQL 0.65% Minor defect : AQL 1.0%
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION 13.3 INSPECTION STANDARDS
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
22
13.3.1 VISUAL DEFECTS CLASSIFICATION TYPE OF DEFECT INSPECTION ITEM DEFECT FEATURE * DEFECT TO MISS SPECIFIED DISPLAY FUNCTION, FOR ALL AND SPECIFIED DOTS EX: DISCONNECTION, SHORT CIRCUIT ETC * NO LIGHT * FLICKERING AND OTHER ABNORMAL ILLUMINATION * SUBJECT TO INDIVIDUAL ACCEPTANCE SPECIFICATIONS * BLACK/WHITE SPOT * BUBBLES ON POLARIZER * NEWTON RING * BLACK/WHITE LINE * SCRATCH * CONTAMINATION * LEVER COLOR SPREED * STAINS * SCRATCHES * FOREIGN MATTER * INSUFFICIENT SOLDER * SOLDERED IN INCORRECT POSITION * CONVEX SOLDERING SPOT * SOLDER BALLS * SOLDER SCRAPS * LIGHT LINE AQL
1.DISPLAY ON MAJOR DEFECT 2.BACKLIGHT 3.DIMENSIONS
0.65
1.DISPLAY ZONE
MINOR DEFECT
2.BEZEL ZONE
1.0
3.SOLDERING
4.DISPLAY ON (ALL ON)
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
CRITERIA
1
23
13.3.2 MODULE DEFECTS CALSSIFICATION
NO. 1. ITEM DISPLAY ON INSPECTION OVERALL DIMENSIONS (1)INCORRECT PATTERN (2)MISSING SEGMENT (3)DIM SEGMENT (4)OPERATING VOLTAGE BEYOND SPEC (1)OVERALL DIMENSION BEYOND SPEC (1) SPOTS AVERAGE DIAMETER NUMBER OF PIECES MINIMUM (mm): D PERMITTED SPACE IGNORE D0.2 5 10 mm 0.2Area A B Judgment Criteria Bright Dot Dark Dot 3 3 5 5 Total 4 5
1/5
2.
3.
BLACK SPOTS, FOREIGN MATTER, AND WHITE SPOTS (INCLUDING LIGHT LEAKAGE DUE TO POLARIZING PLATES PINHOLES, ETC.)
4.
BLACK LINE WHITE LINE NON-DISPLAY
5
BLACK LINE WHITE LINE ON-DISPLAY
6.
SCRATCHES AND DENT ON GLASS POLARIZER
Note : A/B Area Definition
1/5 3/5 B Area 1/5
7.
DOT DEFECT ON DISPLAY
(1)It is defined as Point Defect if defect area>0.5dot (2)It is ignored if defect area0.5dot (3)Weak point defect will be defined as Bright Dot if it can be observed through ND filter 6% (4)The distance between 2 dot defect5mm (5)Not Allowed Joint point defect
3/5
A Area
1/5
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
24
NO.
ITEM CRITERIA LINE DEFECT ON OBVIOUS VERTICAL OR HORIZONTAL LINE DEFECT IS 8 DISPLAY NOT ALLOW MURA ON DISPLAY IT'S OK IF MURA IS SLIGHT VISIBLE THROUNG 6% ND 9 FILTER (1)THE FOLLOWING CF FAIL , SPOT ARE WITHIN THE VIEWING AREA PERMISSIBLE NO. Note Diameter D=(a+b)/2 SIZE D CF FAIL/SPOT ON IGNORED 10 D 0.15mm b DISPLAY 0.15mm 0.2mm NOT ALLOWED UNEVEN COLOR 11 SPREAD , COLORATION BEZEL 12 APPEARANCE (1)TO BE DETERMINED BASED UPON THE STANDARD SAMPLE.
(1)BEZEL MAY NOT HAVE RUST, E DEFORMED OR HAVE FINGER PRINTS STAINS OF OTHER CONTAMINATION. (2)BEZEL MUST COMPLY WITH JOB SPECIFICATIONS.
(1)NO SOLDERING FOUND ON THE SPECIFIED PLACE (2)INSUFFICENT SOLDER (a)LSI, IC A POOR WETTING OF SOLDER IS BETWEEN LOWER BEND OR "HEEL" OF LEAD AND PAD SOLDER FILLET
13 SOLDERING (b)CHIP COMPONENT SOLDER IS LESS THAN 50% OF SIDES AND FRONT FACE WETTING SOLDER FILLET 1/2
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
25
NO.
ITEM
CRITERIA * SOLDER WETS 3 SIDES OF TERMINAL, BUT LESS THAN 25% OF SIDES AND FRONT SURFACE AREA ARE COVERED SOLDER
(3)PARTS ALIGMENT (a)LSI, IC LEAD WIDTH IS MORE THAN 50% BEYOND PAD OUTLINE
13. SOLDERING
(b)CHIP COMPONENT COMPONENT IS OFF CENTER, AND MORE THAN 50% OF THE LEADS IS OFF THE PAD OUTLINE
02101300-01-02
www..com
EMERGING
NO. ITEM
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
26
13. SOLDERING
14. BACKLIGHT
GENERAL 15. APPEARANCE
CRITERIA (4)NO UNMELTED SOLDER PASTE MAY BE PRESENT ON THE PCB. (5)NO COLD SOLDER JOINTS, MISSING SOLDER CONNECTIONS, OXIDATION OR ICICLE. (6)NO RESIDUE OR SOLDER BALLS ON PCB. (7)NO SHORT CIRCUITS IN COMPONENTS ON PCB. (1)NO LIGHT (2)FLICKERING AND OTHER ABNORMAL ILLUMINATION (3)SPOTS OR SCRATCHES THAT APPEAR WHEN LIT MUST BE JUDGED USING LCD SPOT, LINES AND CONTAMINATION STANDARDS. (4)BACKLIGHT DOESN'T LIGHT OR COLOR IS WRONG. (1)NO OXIDATION,CONTAMINATION, URVES OR,BENDS ON INTERFACE PIN (OLB) OF TCP. (2)NO CRACKS ON INTERFACE PIN (OLB) OF TCP. (3)NO CONTAMINATION, SOLDER RESIDUE OR SOLDER BALLS ON PRODUCT. (4)THE IC ON THE TCP MAY NOT BE DAMAGED, CIRCUITS. (5)THE UPPERMOST EDGE OF THE PROTECTIVE STRIP ON THE INTERFACE PIN MUST BE PRESENT OR LOOK AS IF IT CAUSE THE INTERFACE PIN TO SEVER. (6)THE RESIDUAL ROSIN OR TIN OIL OF SOLDERING (COMPONENT OR CHIP COMPONENT) IS NOT BURNED INTO BROWN OR BLACK COLOR. (7)SEALANT ON TOP OF THE ITO CIRCUIT HAS NOT HARDENED. (8)PIN TYPE MUST MATCH TYPE IN SPECIFICATION SHEET. (9)LCD PIN LOOSE OR MISSING PINS. (10)PRODUCT PACKAGING MUST THE SAME AS SPECIFIED ON PACKAGING SPECIFICATION SHEET. (11)PRODUCT DIMENSION AND STRUCTURE MUST CONFORM TO PRODUCT SPECIFICATION SHEET. (12)THE APPEARANCE OF HEAT SEAL SHOULD NOT ADMIT ANY DIRT AND BREAK.
02101300-01-02
www..com
EMERGING
NO. ITEM
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
27
CRITERIA THE LCD WITH EXTENSIVE CRACK IS NOT ACCEPTABLE General glass chip : a b c t/2 < VIEWING AREA 1/8X t/2 > , 2t W/2 1/8X *W=DISTANCE BETWEEN SEALANT AREA AND LCD PANEL EDGE X = LCD SIDE LENGTH t = GLASS THICKNESS
16. CRACKED GLASS
a b c t/2 < VIEWING AREA 1/8X > t/2 , 2t W/2 1/8X *W=DISTANCE BETWEEN SEALANT AREA AND LCD PANEL EDGE X=LCD SIDE LENGTH t=GLASS THICKNESS CHIP ON ELECTRODE PAD a b c t 0.5mm 1/8X * X=LCD SIDE WIDTH t =GLASS THICKNESS a b c t 1/8X L *X=LCD SIDE WIDTH t = GLASS THICKNESS L=ELECTRODE PAD LENGTH Corner part:
IF GLASS CHIPPING THE ITO TERMINAL, OVER 2/3 OF THE ITO MUST REMAIN AND BE , INSPECTED ACCORDING TO ELECTRODE TERMINAL SPECIFICATIONS IF THE PRODUCT WILL BE HEAT SEALED BY THE CUSTOMER, THE ALIGNMENT MARK MUST NOT BE DEMAGED
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION 13.4 RELIABILITY TEST 13.4.1 NO 1 2 3 4 5
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
28
STANDARD SPECIFICATIONS FOR RELIABILITY OF LCD MODULE
ITEM DESCRIPTION High temperature The sample should be allowed to stand at +60C for 240 hrs operation Low temperature The sample should be allowed to stand at -10C for 240 hrs operation High temperature The sample should be allowed to stand at +70c for 240 hrs storage Low temperature The sample should be allowed to stand at -20C for 240 hrs storage High temp / humidity test
The sample should be allowed to stand at 60C , 90% RH 240 hrs The sample should be allowed to stand the following 200 Thermal shock cycles of operation: 6 (not operated ) -25c for 30 minutes ~ +70c for 30 minutes ESD AIR DISCHARGE 4KV 7 (Electrostatic CONTACT DISCHARGE 2KV Discharge ) NOTE (1) : THE TEST SAMPLES HAVE RECOVERY TIME FOR 2 HOURS AT ROOM TEMPERATURE BEFORE THE FUNCTION CHECK. IN THE STANDARD CONDITIONS , THERE IS NO DISPLAY FUNCTION NG ISSUE OCCURRED.
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
29
13.5 TESTING CONDITIONS AND INSPECTION CRITERIA For the final test the testing sample must be stored at room temperature for 24 hours, after the tests listed in table 12.5 , standard specifications for reliability have been executed in order to ensure stability . NO 1 2 3 ITEM Current consumption Contrast Appearance INSPECTION CRITERIA The current consumption should Refer To Specification conform to the product specification. After the tests have been executed, Refer TO Specification the contrast must be larger than half of its initial value prior to the tests. Visual inspection Defect free TEST MODEL
02101300-01-02
www..com
EMERGING
DISPLAY
MODEL NO .
VERSION
PAGE
TECHNOLOGIES CORPORATION 13.6 OPERATION 13.6.1 13.6.2
E T 0 3 5 0 0 9 D H 6 (RoHS)
1
30
13.6.3 13.6.4
Do not connect or disconnect modules to or from the main system while power is being supplied . Use the module within specified temperature ; lower temperature causes the retardation of blinking speed of the display ; higher temperature makes overall display discolor . When the temperature returns to normality , the display will operate normally . Adjust the LC driving voltage to obtain the optimum contrast . Power On Sequence input signals should not be supplied to LCD module before power supply voltage is applied and reaches the specified value . If above sequence is not followed , CMOS LSIs of LCD modules may be damaged due to latch - up problem .
13.7 NOTICE 13.7.1 13.7.2 13.7.3 Use a grounded soldering iron when soldering connector I/O terminals . For soldering or repairing , take precaution against the temperature of the soldering iron and the soldering time to prevent peeling off the through-hole-pad . Do not disassemble . EDT shall not be held responsible if the module is disassembled and upon the reassembly the module failed . Do not charge static electricity , as the circuit of this module contains CMOS LSIs. A workman's body should always be static-protected by use of an ESD STRAP . Working clothes for such personnel should be of static-protected material . Always ground the electrically-powered driver before using it to install the LCD module. While cleaning the work station by vacuum cleaner, do not bring the sucking mouth near the module ; static electricity of the electrically-powered driver or the vacuum cleaner may destroy the module . Don't give external shock. Don't apply excessive force on the surface. Liquid in LCD is hazardous substance. Must not lick and swallow. When the liquid is attach to your, skin, cloth etc. Wash it out thoroughly and immediately. Don't operate it above the absolute maximum rating. Storage in a clean environment, free from dust, active gas, and solvent. Store without any physical load. Rewiring: no more than 3 times .
13.7.4
13.7.5 13.7.6 13.7.7 13.7.8 13.7.9 13.7.10 13.7.11
02101300-01-02

▲Up To Search▲

Price & Availability of ET035009DH6

	To Download ET035009DH6 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .