 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Tube Liquid Sensor OPB350 Series Features: * Can identify if liquid is present in clear tubes that have an outside diameter of 1/8" (3.2mm), 3/16" (4.8mm) or 1/4" (6.3mm) * Opaque plastic housing enhances ambient light rejection * Printed circuit board mounting or 24" (610 mm) wires "N" Package Product Photo Here "T" Package Description: The OPB350 series liquid sensor is designed to work with 1/8" (3.2mm), 3/16" (4.8mm) and 1/4" (6.3mm) outside diameter clear tubes. When output reference circuitry is added, multiple output states such as "fluid present," "no fluid present" and "no tube present" can be recognized. Clear liquid present causes the phototransistor to sink the maximum current, while dark liquid present causes it to sink the minimum current. As bubbles pass through the tube, the signal will vary between the "liquid present" and "no liquid" states. If no liquid is present, the phototransistor sinks only a small amount of current. If no tube is present, the phototransistor sinks a larger current than in the "no liquid" state. Smaller outside diameter tubes can be used when the tube is sized up to one of the standard sizes and is fitted properly in the housing opening. For example, fluid in a 1/16" (1.6mm) outside diameter tube can be sensed when a piece of tubing with a 1/8" (3.2mm) outside diameter and a 1/16" (1.6mm) inside diameter is used as an adapter. Applications: * * * * * * Non-contact fluid sensing IV fluid Oils and other petroleum products Colored fluids Toner fluids Water OPB350 OPB350L187 OPB350L250 OPB350W187Z T OPB350W250Z N Part Number Package Ordering Information LED Peak Wavelength Sensor Tube Size 0.125" 0.187" 890 nm Transistor 0.250" 0.187" 24" / 26 AWG Wire 0.250" 0.330" / 0.320" Lead Length / Spacing Typical Application Circuit Vcc R1=500 R3=750 R1=1K 4 Vth 1 C1=0.1 uf C1=0.1 uf Vth 2 Opto Switch LM339 or LM393 Output 1 Gnd Vth 1 R4=2.5K R4=2K OPB350 Vcc LM339 or LM393 R2=2K Output 2 Vth 2 Gnd RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 02/06 Page 1 of 4 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Tube Liquid Sensor OPB350 Series OPB350 Pin # 1 2 LED Anode Cathode Pin # Transistor 3 4 Collector Emitter 1 3 2 4 Dot OPB350L187 and OPB350L250 LED Anode Cathode 1 Pin # 1 2 Pin # Transistor 3 4 3 Collector Emitter Dot Dot 2 4 OPB350W187Z and OPB350W250Z Pin # Red Black LED Anode Cathode Pin # White Green Transistor Collector Emitter Red-1 White-3 Black-2 Green-4 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 02/06 Page 2 of 4 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Tube Liquid Sensor OPB350 Series Absolute Maximum Ratings (TA=25C unless otherwise noted) Storage Temperature Operating Temperature Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] LED Forward DC Current Peak Forward Current (2 s pulse width, 0.1% duty cycle) Reverse DC Voltage Power Dissipation Output Phototransistor Collector-Emitter Voltage Collector DC Current Power Dissipation 25 or 30 V 50 mA 100 mW 50 mA 1A 2V 100 mW (2) -40 C to +100 C -40 C to +85 C 260 C Electrical Characteristics (TA = 25C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input LED (See OPB245 for additional information -- for reference only) VF IR Forward Voltage Reverse Current 1.8 100 V A IF = 20 mA VR = 2.0 V Output Phototransistor (See OPB555 [PB350] & OP750 [-187 & -250] for additional information -- for reference only) V(BR)CEO ICEO Collector-Emitter Breakdown Voltage OPB350 -187 & -250 30 25 100 V nA IC = 100 A, EE = 0 mw/cm2 VCE = 10 V, IF = 0, EE = 0 mw/cm2 Collector-Emitter Dark Current Coupled (Tested using clear 0.125" O.D., 0.062 I.D. nylon tubing) VCE(SAT) Collector-Emitter Saturation Voltage On-State Collector Current OPB350 OPB350L187 & OPB350W187 OPB350L250 & OPB350W250 OPB350 OPB350L187 & OPB350W187 OPB350L250 & OPB350W250 1 1 0.75 3.5 2 1.5 3 2.3 2.3 0.4 6 4 3 V mA mA mA IC = 100 A, IF = 5 mA VCE = 0.4 V, IF = 5 mA VCE = 0.4 V, IF = 5 mA VCE = 0.4 V, IF = 5 mA VCE = 0.4 V, IF = 5 mA , I.D.=0.0625" VCE = 0.4 V, IF = 5 mA , I.D.=0.0870" VCE = 0.4 V, IF = 5 mA , I.D.=0.1250" IC(ON) On/Off Ratio Notes: (1) All parameters tested using pulse technique. (2) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (3) Methanol or isopropanol are recommended as cleaning agents. The plastic housing is soluble in chlorinated hydrocarbons and keytones. (4) Derate linearly 1.33 mW/ C above 25 C. (5) Ee(APT) is a measurement of the average apertured radiant energy incident upon a sensing area 0.250" (6.350 mm) in diameter, which is perpendicular to and centered to the mechanical axis of the emitting surface at a distance of 0.466" (11.837 mm). Ee(APT) is not necessarily uniform within the measured area. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 02/06 Page 3 of 4 Tube Liquid Sensor OPB350 Series Typical VSAT vs Temperature 0.09 0.08 1.2 Normalized IC(ON) vs Temperature Normalized @ T=20C ( ) 1.0 0.07 0.05 0.04 0.03 0.02 Relative I C(ON) Normalized @ IF = 5mA, ICE = 100uA V SAT (Volts) 0.06 0.8 0.6 0.4 0.2 0.01 0.00 -40 -20 0 20 40 60 80 100 Temperature (C) 0.0 -40 -20 0 20 40 60 80 100 Temperature (C) Rise & Fall Time vs Load Resistance 300 VR2 = 1.0 250 Fall Test Circuit (Rise & Fall Time) Rise & Fall Time (usec) 200 150 100 50 Rise 0 1 2 3 4 5 6 7 8 9 10 Load Resistance (,000 Ohms) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 02/06 Page 4 of 4 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com |
Price & Availability of OPB350W187Z
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |