|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
PQ1CZ21H2Z PQ1CZ21H2Z s Features 1. Maximum switching current:1.5A 2. Low dissipation current at OFF-state (Iqs=Max. 1A) 3. Built-in oscillation circuit (Oscillation frequency:TYP.100kHz) 4. Built-in overheat/overcurrent protection function 5. Variable output voltage (Output variable range:Vref to 35V/-Vref to -30V) [Possible to select step-down output/inversing output according to external connection circuit] PQ1CZ21H2ZZ:sleeve-packaged product PQ1CZ21H2ZP:tape-packaged product Low Dissipation Current at OFF-state Chopper Regulator s Outline Dimensions 6.6MAX. 5.2 0.5 3 (Unit : mm) 2.30.5 (0.5) Epoxy resin 9.7MAX. 5.50.5 1CZ21H (1.7) (0 to 0.25) 4-(1.27) (0.5) 1 2 3 1 2 3 4 5 4 5 2.5 MIN. s Applications 1. Facsimiles 2. Printers 3. Switching power supplies s Absolute Maximum Ratings Parameter Input voltage Output adjustment terminal voltage Dropout voltage *2 Output-COM voltage *3 ON/OFF control voltage Switching current *4 Power dissipation *5 Junction temperature Operating temperature Storage temperature *6 Soldering temperature *1 (Ta=25C) Unit V V V V V A W C C C C VIN VOUT GND (Common to heat sink) OADJ ON/OFF control ( ) : Typical dimensions Symbol Rating VIN 40 VADJ 7 VI-O 41 VOUT -1 VC -0.3 to +40 1.5 ISW 8 PD Tj 150 Topr -40 to +85 Tstg -40 to +150 Tsol 260 *1 Voltage between VIN terminal and COM terminal *2 Voltage between VOUT terminal and COM terminal *3 Voltage between ON/OFF control and COM terminal *4 PD:With infinite heat sink *5 Overheat protection may operate at the condition Tj:125C to 150C *6 For 10s Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://www.sharp.co.jp/ecg/ (0.9) +0.2 0.5-0.1 PQ1CZ21H2Z s Electrical Characteristics Parameter (Unless otherwise specified, condition shall be VIN=12V, IO=0.2A, VO=5V, ON-OFF terminal=2.7V, Ta=25C) MIN. TYP. MAX. Unit Symbol Conditions VSAT Output saturation voltage Reference voltage Reference voltage temperature fluctuation Load regulation Line regulation Efficiency Oscillation frequency Oscillation frequency temperature fluctuation Overcurrent detecting level ON threshold voltage Output ON control current Output OFF control current Stand-by current Output OFF-state consumption current Vref Vref |RegL| |RegI| fO fO IL VTH(ON) IC (ON) IC (OFF) ISD IQS ISW=1A - Tj=0 to 125C IO=0.2 to 1A VIN=8 to 35V IO=1A - Tj=0 to 125C No L, C, D 4 terminal=0V, 5 terminal 5 terminal=2.7V 5 terminal=0.4V VIN=40V, 5 terminal=0V VIN=40V, 4 terminal=3V - 1.235 0.9 1.26 1.5 1.285 - - - - 80 - 1.55 0.8 - - - - 0.5 0.1 0.5 82 100 3 2 1.5 - - - 8 - 1.5 2.5 - 120 - 2.6 2 200 2 1 12 V V % % % % kHz % A V A A A mA Fig.1 Standard Test Circuit 4 1 ISD Iqs PQ1CZ21H2Z 5 + VIN CIN 100F A IC (ON) IC (OFF) 3 D R1 1k CO 470F R2 + Load 2 L 210H IO VO A ON/OFF control logic 5 pin Output LOW OFF HIGH ON OPEN OFF L : HK-14D100-2110 (made by Toho Co.) D :ERC80-004 (made by Fuji electronics Co.) Fig.2 Power Dissipation vs. Ambient Temperature 10 PD : With infinite heat sink Fig.3 Overcurrent Protection Characteristics (Typical value) 7 6 Output voltage VO (V) 5 4 3 2 1 Ta=25C VIN=12V VO=5V 8 Power dissipation PD (W) 5 0 -40 -20 0 0 20 40 60 80 85 0 0.5 1 1.5 2 2.5 3 3.5 4 Ambient temperature Ta (C) Output current IO (A) Note) Oblique line prtion:Overheat protection may operate in this area PQ1CZ21H2Z Fig.4 Efficiency vs. Input Current 100 Tj=25C 90 Efficiency (%) VO=12V, IO=1A VO=12V, IO=0.2A Output saturation voltage VSAT (V) Fig.5 Switching Current vs. Output Saturation Voltage 1.2 Tj=25C 1 0.8 80 VO=5V, IO=1A 70 VO=5V, IO=0.2A 0.6 0.4 60 0.2 0 50 0 10 20 Input voltage VIN (V) 30 40 0 0.5 1 1.5 2 Switching current ISW (A) Fig.6 Reference Voltage Fluctuation vs. Junction Temperature 2 Reference voltage fluctuation Vref (%) VIN=12V VO=5V Fig.7 Load Regulation vs. Output Current 1 Tj=25C VIN=12V VO=5V Load regulation RegL(%) 0.5 1 0 0 -1 -2 -50 -25 -0.5 0 25 50 75 100 125 0 0.2 0.4 0.6 0.8 1 1.2 Junction temperature Tj (C) Output current IO (A) Fig.8 Line Regulation vs. Input Voltage 1 Fig.9 Oscillation Frequency Fluctuation vs. Junction Temperature 2 Oscillation frequency fluctuation fO (%) VIN=12V VO=5V 0 -2 -4 -6 -8 -10 -50 Line regulation RegI (%) 0.5 0 Tj=25C VO=5V IO=0.2A -0.5 0 5 10 15 20 25 30 35 40 Input voltage VIN (V) -25 0 25 50 75 100 125 Junction temperature Tj (C) PQ1CZ21H2Z Fig.10 Overcurrent Detection Level Fluctuation vs. Junction Temperature 6 Overcurrent detecting level fluctuation IL (%) 4 2 0 -2 -4 -6 -8 -50 -25 Fig.11 ON Threshold Voltage vs. Junction Temperature 2 VIN=12V ON threshold voltage VTH (ON) (V) 1.5 1 0.5 0 25 50 75 100 125 0 -50 -25 0 25 50 75 100 125 150 Junction temperature Tj (C) Junction temperature Tj (C) Fig.12 Operating Consumption Current vs. Input Voltage 10 Operating consumptioon current IQ' (mA) Tj=25C VO=5V 9 IO=1A 8 IO=0.2A 7 No load 6 5 0 10 20 Input voltage VIN (V) 30 40 Fig.13 Power Dissipation vs. Ambient Temperature (Typical Value) 3 Cu area 740mm2 Power dissipation PD (W) 2 Cu area 180mm2 Cu area 100mm2 Cu area 70mm2 1 Cu area 36mm2 Material : Glass-cloth epoxy resin Size : 50x50x1.6mm Cu thickness : 35m 20 40 60 80 85 PWB PWB Cu 0 -40 -20 0 Ambient temperature Ta (C) PQ1CZ21H2Z Fig.14 Block Diagram 1 2 Voltage regulator _ PWM COMP. + 5 ON/ OFF Overcurrent detection circuit F/F Q R S OSC. 1 2 3 4 5 VIN VOUT GND (Common to heat sink) Oadj ON/OFF control ERROR AMP. _ + Vref 4 Overheat detection circuit 3 Fig.15 Step Down Type Circuit Diagram (5V output) 4 1 PQ1CZ21H2Z 5 + VIN 8 to 35V 3 CIN 100F D R1 1k CO 470F R2 3k + Load 2 L 210H VO 5V ON/OFF control signal Fig.16 Polarity Inversion Type Circuit Diagram (-5V output) 4 1 PQ1CZ21H2Z 5 + VIN 5 to 30V 3 CIN 100F D 2 L 130H R2 3k + Load CO 2200F R1 1k VO -5V ON/OFF control signal PQ1CZ21H2Z s Precautions for Use 1. External connection (1) Wiring condition is very important. Noise associated with wiring inductance may cause problems. For minimizing inductance, it is recommended to design the thick and short pattern (between large current diodos, input/output capacitors, and terminal 1,2.) Single-point grounding (as indicated) should be used for best results. (2) High switching speed and low forward voltage type schottky barrier diode should be recommended for the catch-diode D because it affects the efficiency. Please select the diode which the current rating is at least 1.2 times greater than maximum swiching current. (3) The output ripple voltage is highly influenced by ESR(Equivalent Series Resistor)of output capacitor, and can be minimized by selecting Low ESR capacitor. (4) An inductor should not be operated beyond its maximum rated current so that it may not saturate. (5) When voltage that is higher than VIN 1 , is applied to VOUT 2 , there is the case that the device is broken. Especially, in case VIN 1 is shorted to GND in normal condition, there is the case that the device is broken since the charged electric charge in output capacitor (CO) flows into input side. In such case a schottly barrier diode or a silicon diode shall be recommended to connect as the following circuit. 4 1 PQ1CZ21H2Z 5 VIN + CIN + D CO R1 R2 L 2 VO 3 Load C-MOS or TTL 1 PQ1CZ21H2Z 2 PQ1CZ21H2Z s Thermal Protection Design Internal power dissipation(P)of device is generally obtained by the following equation. P=ISW(Average.) x VSATxD' + VIN(voltage between VIN to COM terminal)x IQ'(consumption current) Step down type -------------- Ton VO+VF D'(Duty)= -------- = ------------- T(period) VIN-VSAT+VF ISW(Average)= IO(Output current.) Polarity inversion type -------------------- |VO|+VF Ton D'(Duty)= -------- = -------------------- T(period) VIN+|VO|-VSAT+VF 1 ISW(Average)= -------- x IO(Output current.) 1-D' VF : Forward voltage of the diode When ambient temperature Ta and power dissipation PD(MAX)during operation are determined, use Cu plate which allows the element to operate within the safety operation area specified by the derating curve. Insufficient radiation gives an unfavorable influence to the normal operation and reliability of the device. s ON/OFF Control Terminal 1. In the following circuit,when ON/OFF control terminal 5 becomes low by switching transistor Tr on, output voltage may be turned OFF and the device becomes stand-by mode. Dissipation current at stand-by mode becomes Max.1A. 2. ON/OFF control terminal 5 is compatible with LS-TTL. It enables to be directly drive by TTL or C-MOS standard logic (RCA4000 series). If ON/OFF control terminal is not used, it is recommended to directly connect applicable terminals with input terminal. 4 1 PQ1CZ21H2Z 5 + VIN 3 CIN D R1 CO R2 + Load 2 L IO VO C-MOS or TTL Application Circuits NOTICE qThe circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. qContact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. qObserve the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). qContact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. qIf the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. qThis publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. qContact and consult with a SHARP representative if there are any questions about the contents of this publication. 115 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |