MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER [ Features ] This IC is 1 chip driver IC for spindle motor and 5 channel actuators. All of the motor and actuator of optical disk drive system (CD-ROM etc.) can be drived by only this IC. This IC has a direct PWM control system for Spindle and Slide channels drive due to reducing IC power dissipation. This IC has three voltage supply terminals (for Spindle, Slide,Focus/Tracking and Loading) , and three voltage supply can be set separately. Further more this IC has short braking select function,FG amplifier, thermal shut down circuit, standby circuit, reverse rotation detect circuit. PIN CONFIGURATION SL1IN SL2IN VM2 RSL2 SL2+ SL2GND RSL1 SL1+ SL1GND W V U RSP HwHw+ HvHv+ HuHu+ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 (Top View) 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 OSC MU1 LOINLOIN+ BRS LOLO+ FOFO+ GND TO+ TO5VCC GND TOIN FOIN SPIN REF FG HB VM1 [ APPLICATION ] Package outline : 42 PIN POWER SSOP (42P9R-B) CD-ROM, DVD, DVD-ROM, DVD-RAM ,Optical disc related system,etc [ BLOCK DIAGRAM ] s FG FG Reverse Detect s s s HU+ HUHV+ HVHW+ HWHB Hall Bias CTL amp. Direction comp. Current comp. CTL amp. Direction comp. Current comp. CTL amp. Direction comp. Current comp. 120 MATRIX Logic Logic TSD MU1 SPIN REF SL1IN SL2IN BIAS Frequency generator OSC FOIN TOIN Regulator 5V power supply X5 X5 X5 (1 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER [ PIN FUNCTION ] TERMINAL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 SYMBOL SL1IN SL2IN VM2 RSL2 SL2+ SL2GND RSL1 SL1+ SL1GND W V U RSP HWHW+ HVHV+ HUHU+ TERMINAL FUNCTION Slide control voltage input 1 Slide control voltage input 2 Motor Power Suppry 3 (for Slide) Slide current sense 2 Slide non-inverted output 2 Slide inverted output 2 TERMINAL 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 SYMBOL OSC MU1 LOINLOIN+ BRS LOLO+ FOFO+ GND TO+ TO5VCC GND TOIN FOIN SPIN REF FG HB VM1 TERMINAL FUNCTION PWM carrier oscilation set mute 1 Loading control input(-) Loading control input(+) Brake select control terminal Loading inverted output Loading non-inverted output Focus inverted output Focus non-inverted output GND Slide current sense 1 Slide non-inverted output 1 Slide inverted output 1 GND Tracking non-inverted output Tracking inverted output 5V Power Supply (for FS ,TS,LO) GND Motor drive output W Motor drive output V Motor drive output U Spindle current sensie HW- sensor amp. input HW+ sensor amp. input HV- sensor amp. input HV+ sensor amp. input HU- sensor amp. input HU+ sensor amp. input GND Tracking control voltage input Focus control voltage input Spindle control voltage input Reference voltage input Frequency generator output Bias for Hall Sensor Motor Power Suppry 1 (for Spindle) (2 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER [ABSOLUTE MAXIMUM RATING] SYMBOL PARAMETER 5V power supply Motor power supply 1 Motor power supply 2 Motor Output Current A Spindle and Slide output current Motor Output Current B Maximum input voltage of terminals Power dissipation Thermal derating Junction temperature Operating temperature Storage temperature *note 1 (Ta=25C) CONDITIONS Focus,Tracking and Loading power supply Spindle power supply Slide power supply Focus,Tracking and Loading output current RATING Unit 5VCC VM1 VM2 IoA IoB Vin Pt K Tj Topr Tstg 7 15 15 1.0 1.2 0 to 5VCC 2.6 20.8 150 -20 to +75 -40 to +150 V V V A A V W mW / C C C C MU1,Hw-,Hw+,Hv,Hv+,Hu-,Hu+,REF,SPIN,BRS TOIN,FOIN,OSC,SLIN1,SLIN2,LOIN-,LOIN+ Free Air and on the grass epoxy board Free Air and on the grass epoxy board *note1 ; The ICs must be operated within the Pt (power dissipation) or the area of safety operation The spindle and slide output terminal is needed external shottky diode between each output and GND when it is used above 0.6A. Discription(IoA) is case of with external shottky diode. [RECOMMENDED OPERATING CONDITIONS] (Ta=25C) LIMITS SYMBOL PARAMETER VM1 power supply(for Spindle) VM2 power supply(for Slide) 5V power supply(for FS,TS,LO) *note 2 SpindleandSlideOutputCurrent minimum 6 4.5 4.5 typical 12 12 5 0.5 0.5 maximum 13.2 13.2 7 1.0 0.8 120 Unit V V V A A KHz VM1 VM2 5VCC IoA IoB Fosc Focus, Tracking and Loading Output Current PWM carrier frequency 30 *note2 The spindle and slide output terminal is needed external shottky diode between each output and GND when it is used above 0.6A. Discription(IoA) is case of with external shottky diode. (3 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER [THERMAL DERATING] 6.0 (W) 5.0 4.0 using N-type board using P-type board 3.0 2.0 1.0 This IC's package is POWER-SSOP, so improving the board on which the IC is mounted enables a large power dissipation without a heat sink. For example, using an 1 layer glass epoxy resin board, the IC's power dissipation is 2.6W at least. And it comes to 3.6W by using an improved 2 layer board. The information of the N, P type board is shown in attached. 0 25 50 75 100 Ta (C) 125 150 Ambient Temperature [ELECTRICAL CHARACTERISTICS] Common (Ta=25C, 5VCC=5V,VM1=VM2=12V unless otherwise noted.) LIMITS SYMBOL Icc1 Icc2 Fosc PWM carrier frequency VinREF IinREF VMULO VMUHI IMU BRSLO BRSHI IBRS REF input voltage range REF input voltage range MUTE terminal low voltage MUTE terminal high voltage Mute terminal input current BRS terminal low voltage BRS terminal high voltage BRS terminal input current VREF=1.65V MU1 MU1 MU1 BRS BRS BRS at 5V input voltage at 5V input voltage PARAMETER CONDITIONS 5VCC,VM1, VM2 current MU1=5V MIN TYP MAX Unit mA A KHz Supply current Sleep current 60 0 65 1.0 -10 78 30 5VCC,VM1, VM2 current under Sleep (MU1 = 0V) OSC : with 330pF 3.3 +10 0.8 V A V V 3.0 500 0.8 3.0 430 A V V A (4 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER [ELECTRICAL CHARACTERISTICS] Spindle (Ta=25C, 5VCC=5V,VM1=VM2=12V unless otherwise noted.) LIMITS SYMBOL Vdyc1 Vdead1Vdead1+ Vin1 Gvo1 Vlim1F Vlim1R PARAMETER CONDITIONS MIN TYP MAX Unit V Dynamic range of output Io=0.5 [A] SPIN[10.3 -80 0 0 0.85 0.4 0.22 1.3] 10.8 -40 +40 0 +80 5 1.0 0.5 0.28 1.15 0.6 0.34 3.7 mV mV V V/V V V V Controlvoltagedeadzone 1 REFControlvoltageinputrange1 Control gain 1 Control limit 1F Control limit 1R Ilim1R=Vlim1R/ Rs [A] Hu+,Hu-,Hv+,Hv-,Hw+ ,Hw- VHcom Hall sensor amp. common mode input range VHmin Hall sensor amp. input signal level Hu+,Hu-,Hv+,Hv-,Hw+ ,Hw- 60 0.6 0.85 1.2 30 mVp-p VHB IHB HB output voltage HB terminal sink current at Load current (IHB)=10mA MU1=5V V mA Slide 1,2 (Ta=25C, 5VCC=5V,VM1=VM2=12V unless otherwise noted.) LIMITS SYMBOL Vdyc2 Vdead2Vdead2+ Control voltage dead zone 2 Vin2 Gvo2 Vlim2 Tdon Tdoff Tdsw Ileak Control voltage input range 2 PARAMETER Dynamic range of output CONDITIONS Io=0.5 [A] SL1IN,Sl2IN < REF REF < SL1IN ,SL2IN SL1IN,SL2IN at VM2=5[V] at VM2=12[V] MIN TYP MAX Unit V 3.3 10.3 -80 0 0 0.85 0.43 3.8 10.8 -30 +30 0 +80 5 1.0 0.5 1.0 2.0 3.0 1.15 0.58 2.0 3.5 6.0 100 mV mV V V/V V Control gain 2 Control limit 2 Output turn-on delay Output turn-off delay Output switching delay Output leak current Gio2=Gvo2/ Rs [A/V] Ilim2=Vlim2/ Rs [A] sec sec sec A MU1=5v -100 (5 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER [ELECTRICAL CHARACTERISTICS] Loading (Ta=25C, 5VCC=5V,VM1=VM2=12V unless otherwise noted.) LIMITS SYMBOL Vdyc3-1 Vdyc3-2 Vin3 Gvo3 Voff1-1 Voff1-2 PARAMETER CONDITIONS Io=0.5[A] MIN TYP MAX Unit V V Dynamic range of output Dynamic range of output R=5.4[] 5VCC=4.75[V],VM1=12[V] LOIN+,LOIN(LO+) - (LO-) (LOIN+) - (LOIN-) (LO+) - (LO-) at LOIN+=LOIN-=5V (LO+) - (LO-) at LOIN+=LOIN-=1.65V 3.8 3.2 0 12.5 -100 -50 4.0 3.4 5 14 0 0 15.2 +100 +50 Controlvoltageinputrange3 V Control gain 3 Output offset voltage Output offset voltage dB mV mV Focus / Tracking (Ta=25C, 5VCC=5V,VM1=VM2=12V unless otherwise noted.) LIMITS SYMBOL Vdyc4 PARAMETER CONDITIONS Io=0.5[A] VM1=12[V] FOIN,TOIN (FO+) -(FO-) FOIN-REF (TO+) -(TO-) TOIN-REF MIN TYP MAX Unit V Dynamic range of output Vin4 Gvo4 Voff2 3.8 0 12.5 -35 4.2 5 14 0 15.2 +35 Controlvoltageinputrange4 V dB mV Control gain 4 Output offset voltage (FO+) -(FO-) at REF=FOIN=1.65V (TO+) -(TO-) at REF=TOIN=1.65V NOTE : This IC need condenser between each supply lines and GND for stoped Oscillation. [THERMAL CHARACTERISTICS] FUNCTION START TEMPERATURE OF IC FUNCTION STOP TEMPERATURE OF IC SYMBOL PARAMETER MIN TYP MAX MIN TYP MAX Unit TSD Thermal Shut Down 160 130 C *note3 This TSD function start temperature doesn't show the guaranteed max. temperature of the devices. The guranteed max. temperature is Tj max. which is shown in "9. ABSOLUTE MAXIMUM RATING". The TSD function is a thermal protection in case the temperature of the devices goes up above Tjmax because of wrong use. And these TSD temperature are the target temperatures for circuit design, not the guranteed temperatures. (The TSD function of all the devices is not checked by a test in high temperature.) (6 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER Standby function Logic control MU1 Loading SELECT2 H On SELECT1 L/Open Off Slide1 On Off Drive Slide2 On Off channel Focus Tracking Spindle On On On Off Off Off This IC has MUTE terminal (MU1). It is possible to control ON / OFF of the channel by external logic inputs. In case of SELECT1, the bias of all circuit becomes OFF. Therefore, this mode is available in order to reduce the power dissipation when the waiting mode. In case of SELECT2,the bias of all channel becomes ON. Regard with making OFF the loading channel in case of SELECT2,please refer to [Loading channel]. Brake select function BRS Hi L / Open SPIN < REF Reverse Brake Short Brake REF < SPIN Forward Forward This IC has BRS terminal (BRS). It is possible for a braking timiming of Spindle drive to select which the short brake or the reverse brake by BRS. It shuould select the short brake in case of high speed system and please change to the reverse brake when the rotation speed becomes enough low. It is available when the SPIN voltage is low than the reference voltage. Loading channel The loading channel is the circuit of BTL voltage drive. This circuit has the referential input. Output swing is determined with Vin x 5. Also,it is possible for this channel to use for the slide motor , the focus coil and the tracking coil. The input terminal is high impedance. It is possible to do variable a gain by external resistor. The output becomes high impedance in case of both input voltage becomes under 0.7 volts. It is possible for the input terminal to operate from 0 volts.The following table and diagram show an application in case of two MCU port and one MCU port for the loading motor.In case of one MCU port, if use three state port, it is possible for this channel to have the stop function. 5VCC LO+ LOIN+ + LOADING Channel LOINLOReverse Vo Forward M (7 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER LO- Output voltage [V] LO+ + Coil - VM3 2 Coil Vo Gvo = 5 [v/v] [LOIN+] - [LOIN-] (V) Vo=[LO+] - [LO-] =5 x ([LOIN+] - [LOIN-]) LO+ application.1 (MCU : Two port H/L control) LO- Logic control P1 P2 5V 5V 5V 0 5V 0 0 0 Situation of loading channel Short brake --> Stop Reverse rotation Forward rotation Off [ High impedance output] Output voltage swing Vo= 0 [V] Vo= - 5x5xR1/(R1+2xR2) Vo= 5x5xR1/(R1+2xR2) Off application.2 (MCU : One port H/Z/L control) Logic control Situation of loading channel P1 5v Forward rotation Z (Hi impedance) Output voltage swing Vo= 2.5[V] x5x R2 (R1/2)+R2+R3 Vo= 0 [V] Vo=- 2.5[V] x5x R2 (R1/2)+R2+R3 5v 5V Short brake --> Stop Reverse rotation P1 0 5v P1 P2 R2 R1 LOIN+ LOINR2 0v 5v 0v P1 Z 0v R1 LOIN+ P1 R3 R2 R1 LOIN- application.1 ( Two port H/L control) P2 application.2 (One port H/Z/L control) (8 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER SPINDLE channel The relationship between the differential voltage between SPIN and REF and the torque is shown in right Figure. The voltage gain[Gvo] is 1.0 [V/V]. The current gain[Gio] is 2.0[A/V] (at sensing resistor : 0.5 ohm,and R1=,R2=0ohm) in forward torque directions, and the dead zone is from 0mV to 60mV (at R1=,R2=0ohm) . The coil current gain under the reverse torque is the same with in forward torque directions.And the limitation function gets on when the differential voltage of VM1(12V) to RSP is 0.5V. Therefore current-gain-control and current-limit of this IC is determined with sensing resister value, and more detail control can be determined with setting a gain-resister outer this IC as below. current limit Forward Torque lim1F Dead zone Gio CTL -REF (V) Gio Dead zone lim1R current limit Reverse Torque The example of current-gain and current-limit of SPINDLE. Rs [] Ilim1F Ilim1R [A] [A] 1.00 0.66 0.50 0.56 0.37 0.28 Gio* [A/V] R1= R2=0 ohm R1=R2 R1=2 * R2 0.50 0.75 1.00 2.00 1.33 1.00 1.00 0.66 0.50 0.66 0.44 0.33 Gio*= R1 / [(R1+R2) * Rs] [A/V] VM1 Rs RSP R2 CTL R1 1.65v REF SPIN 5V Rh HB HU+ HUHV+ HVHW+ HWU V W M GND (9 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER SLIDE channel The relationship between the differential voltage between SLIN and REF and the torque is shown in right Figure. The voltage gain[Gvo] is 1.0 [V/V]. The current gain is 2.0[A/V] (at sensing resistor : 0.5 ohm and R1=,R2=0ohm) in forward torque directions, and the dead zone is from 0mV to 80mV (at R1=,R2=0ohm)). The coil current gain under the reverse torque is the same with in forward torque directions.And the limitation function gets on when the differential voltage of VM2(12V) to RSL is 0.5V. Therefore current-gain-control and current-limit of this IC is determined with sensing resister value. Forward current limit Gio Dead zone SL*IN -REF (V) Dead zone Gio Reverse VM2 VM2 current limit Rs RSL1 Forward R2 CTL R1 1.65v REF SL1IN Rs RSL2 Forward R2 CTL SL2IN SL1+ SL2+ M SL1GND Reverse 1.65v R1 REF M SL2GND Reverse The example of current-gain and current-limit of SLIDE. Gio* [A/V] Rs [] Ilim [A] R1= R2=0 ohm R1=R2 R1=2 * R2 0.50 0.75 1.00 1.00 0.66 0.50 2.00 1.33 1.00 1.00 0.66 0.50 0.66 0.44 0.33 Gio*= R1 / [(R1+R2) * Rs] [A/V] (10 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER FOCUS / TRACKING channel The focus and tracking channel is the voltage control drive using BTL . The focus and tracking is the same composition. The relationship between the differential voltage between FOIN and REF and the output voltage is shown in below Figure. The voltage gain [Gvo] is 5.0 [V/V]. FOIN R 2.5R FO- REF R VM3 2.5R R Coil R R FO+ R FO- Output voltage [V] FO+ + Coil - VM3 2 Coil Vo Gvo = 5 [v/v] FOIN - REF (V) Vo=[FO+] - [FO-] =5 x (FOIN - REF) FO+ (11 / 17) FOREV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER Direct PWM operation The spindle and the slide channel is controlled by the direct PWM control. Also,built-in the current limit circuit. This IC controls the motor current directly. FORWARD Current path timing 1. FORWARD Current path timing 2. VM2 Rs RSL Current path 1 VM2 Rs RSL SL+ M SL- SL+ M SL- GND Current path 2 GND Current path 1 Current path 2 Control value Control value Io=Vrs / Rs Motor current carrier period Time ( 12 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER PWM carrier frequency setting PWM carrier frequency is decided by charging and discharging the capacitor that is connected to OSC terminal outer IC. Examination of the relationship the capacitor connected to OSC terminal and PWM carrier frequency is given in following table. Capacitor [pF] Carrier Frequency [KHz] 820 28 750 30 330 65 220 90 180 110 130 140 110 160 *note) This PWM carrier frequency is TYP value. Recommendation of SHORT BRAKE MODE at SPINDLE DRIVE This IC has two brake mode, PWM-BRAKE-MODE and SHORT-BRAKE-MODE. In this IC recommendation, SHORTBRAKE-MODE is superior to PWM-BRAKE-MODE to reducing the power dissipation and to avoid braking down of this IC. (By excessive reverse torque current in braking a motor with PWM-BRAKE from high-speed-rotation with being excessive Back-EMF, this IC could be broken.) The relationship between hall-amplifier-input and output-current-commutation at SPINDLE DRIVE The relationship between the hall elements and the motor output current is shown in bellow Figure. Hw+ Hall input Hv+ Hu+ Hall elements U V W W V U U V W Outer roter REVERSE SPIN[+] Output current V U W V 0 U W V U W FORWARD SPIN>REF ( 13 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER FG function at SPINDLE DRIVE The FG terminal outputs the square pulse signal synchronizing with the Hall inputs [Hv+, Hv-] timing. And, the FG terminal is open-collector output. Phase delay circuit at SLIDE Phase delay circuit is built in the IC to detect an output spike current, when the motor current direction is switching. In switching the motor current direction, Phase delay circuit switch-off all output trangister of H-bridge for 3sec. Output current setting at SLIDE In this IC, since output tranjister is NPN-type tranjister, motor coil current (Io) is larger than sensing resistance current about 20mA (TYP.) according to base current of output tranjister. Therefore please design output current with consisting these base current. ( 14 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER I/O circuit * FOIN, TOIN, SPIN LOIN+, LOINOPIN5VCC 2K * Hu+, HuHv+, HvHw+, HwREF 5VCC 2K * BRS 2K 8K 10K * HB 5VCC * FG 5VCC 5VCC RSP * VM1, RSP, U, V, W VM1 * MU1 5VCC 2K 8K 30K 5VCC 4K 10K * OSC 5VCC 2K 2K 2K U V W GND * 5VCC, FO+, FO-, TO+, TO-, LO+, LO9Vmax VM1 INSIDE REG 5VCC LO+ LO- TO+ TO- FO+ FO- GND * VM2, RSL, SL1+, SL1-, SL2+, SL2VM2 RSL1 RSL1 SL1+ SL1- SL2+ SL2- GND (15 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER [The boards for thermal derating evaluation] Board material 1st layer [TOP view] Glass-epoxy FR-4 2nd layer [BACK view] Size 70x70mm thickness N-type board t=1.6mm 1 and 2 layers [2 layer] material : copper thickness : t=18m O-type board [2 layer] P-type board [1 layer] POWER-SSOP 42P9R-B Heat sink Lead mounted IC Chip Evaluation board ( 16 / 17) REV990726 MITSUBISHI SEMICONDUCTORS M63020FP SPINDLE MOTOR AND 5CH ACTUATOR DRIVER [APPLICATION CIRCUIT no.1] MCU R12 R11 R9 C1 REF R10 D/A D/A 1 2 5 to 12v Slide RSL2 3 4 5 6 M SLIDE RSL1 7 8 9 10 11 12 13 RSP 14 15 16 17 18 SL1IN SL2IN VM2 RSL2 SL2+ SL2GND RSL1 SL1+ SL1GND W V U RSP HWHW+ HVHV+ HUHU+ OSC MU1 LOINLOIN+ BRS LOLO+ FOFO+ GND TO+ TO5VCC GND TOIN FOIN SPIN REF FG HB VM1 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 R8 R7 R7 Loading M FS 104 5V power Focus Tracking 5V TS R5 R3 R1 1.65v R6 R4 R2 DSP M 19 20 21 10K *Pull-up Resistance Rh 12v External Parts RSP RSL1, RSL2 Rh R1, R2, R3, R4, R5, R6 R7, R8 C1 R9, R10, R11,R12 D1, D2, D3 R13, R14, R15, R16 C2, C3, C4, C5 Typ 0.33 2 200 10K 10K 330p 10K - 22 10n Unit Notes Ilim1F=1.5A, Ilim1R=1.0A, Gain=3.0A/V Ilim=0.5A, Gain=1A/V F V F This is difficult for your specification. This is difficult for your specification. Fosc=65KHz This is difficult for your specification. Recommend VF<0.5V at IL=1.0A ( 17 / 17) REV990726
|